LSI Logic PERC 4/DC, v.351S, A05
AUTOMATISKT INSTALLERAD Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
Dell PowerEdge RAID Controller 4/DC firmware and update script for for IA-64 based platforms. The update script runs under EFI.
Version: 351S
Version: 351S
Rekommenderat
Hitta den bästa nerladdningen för ditt system
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt systemSök efter support
Ange din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare. Visa mig hur
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om. Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
Current Firmware - 351S
(Previous - 350O)
Current BIOS - 1.10
(Previous - 1.09)
Current Ctrl-M - U827
(Previous - U821)
Current Boot Block - 1.7.7Dell
(Previous - 1.7.6Dell)
Fixes
1. Fixed an issue that optimized cache flush algorithms while switching between no read-ahead to read-ahead cache modes.
2. Modified the Fast Initialization function to delete all operation system partition table information.
3. Fixed an issue where a Seagate hard drive model M3637 was not negotiating correctly with PERC 4 adapters.
4. Fixed a SES Timeout error caused by a media error recovery defect in cluster mode on a PERC4/DC and a PERC3/DC.
5. Modified Ctrl-M to clear physical drive media error count upon drive replacement.
Note: System must be powered on during the drive replacement in order for media errors to be cleared.
6. Modified caching algorithms to not switch from Write-back to Write-through during a battery fast charge.
7. Fixed a performance degradation issue when using RAID 10 virtual disks, when configured to use no read ahead or write caching and direct IO on PERC4 controllers.
Enhancements
1. Added Patrol Read feature. Patrol Read involves the review of the system for possible hard drive errors that could lead to drive failure, then action to correct the errors. The goal is to protect data integrity by detecting physical drive failures before the failures can damage data. Patrol Read adjusts the amount of RAID controller resources dedicated to Patrol Read operations based on outstanding disk I/O.
2. Added Rebuild Checkpoint feature. The Dell PERC firmware has a feature to resume a rebuild on a physical drive in case of an abrupt power loss or if the server rebooted in the middle of a rebuild operation.
3. Enhanced write algorithms to increase I/O performance for RAID 5 and RAID 50 virtual disks using four or more disks that are configured to use write-through write cache mode.
Firmware upgrade while controller is doing background I/O task:
The firmware upgrade may fail if any of the RAID controllers in the system are performing an I/O background task. (ie. check consistency, background initialization, rebuild, or reconstruction). Allow the background task to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect a firmware upgrade. Current RAID configuration will not be modified or cleared during the Firmware Upgrade process.
Läs mer(Previous - 350O)
Current BIOS - 1.10
(Previous - 1.09)
Current Ctrl-M - U827
(Previous - U821)
Current Boot Block - 1.7.7Dell
(Previous - 1.7.6Dell)
Fixes
1. Fixed an issue that optimized cache flush algorithms while switching between no read-ahead to read-ahead cache modes.
2. Modified the Fast Initialization function to delete all operation system partition table information.
3. Fixed an issue where a Seagate hard drive model M3637 was not negotiating correctly with PERC 4 adapters.
4. Fixed a SES Timeout error caused by a media error recovery defect in cluster mode on a PERC4/DC and a PERC3/DC.
5. Modified Ctrl-M to clear physical drive media error count upon drive replacement.
Note: System must be powered on during the drive replacement in order for media errors to be cleared.
6. Modified caching algorithms to not switch from Write-back to Write-through during a battery fast charge.
7. Fixed a performance degradation issue when using RAID 10 virtual disks, when configured to use no read ahead or write caching and direct IO on PERC4 controllers.
Enhancements
1. Added Patrol Read feature. Patrol Read involves the review of the system for possible hard drive errors that could lead to drive failure, then action to correct the errors. The goal is to protect data integrity by detecting physical drive failures before the failures can damage data. Patrol Read adjusts the amount of RAID controller resources dedicated to Patrol Read operations based on outstanding disk I/O.
2. Added Rebuild Checkpoint feature. The Dell PERC firmware has a feature to resume a rebuild on a physical drive in case of an abrupt power loss or if the server rebooted in the middle of a rebuild operation.
3. Enhanced write algorithms to increase I/O performance for RAID 5 and RAID 50 virtual disks using four or more disks that are configured to use write-through write cache mode.
Firmware upgrade while controller is doing background I/O task:
The firmware upgrade may fail if any of the RAID controllers in the system are performing an I/O background task. (ie. check consistency, background initialization, rebuild, or reconstruction). Allow the background task to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect a firmware upgrade. Current RAID configuration will not be modified or cleared during the Firmware Upgrade process.
Version
351S, A05
Utgivningsdatum
07 juni 2005
Hämtningstyp
Firmware
Kategori
SCSI RAID
Prioritet
RekommenderasDell Technologies rekommenderar att du installerar den här uppdateringen under nästa schemalagda uppdateringscykel. Uppdateringen innehåller ändringar för att bibehålla det allmänna systemtillståndet. Den säkerställer att systemets programvara förblir aktuell och kompatibel med andra systemmoduler (fast programvara, BIOS, drivrutiner och programvara) och kan inkludera andra nya funktioner.
Tillgängliga format
Filformat: Extern ZipPack
Filnamn: R101840.EXE
Filstorlek: 985.68 KB
Det här är en stor fil. Beroende på din anslutningshastighet kan det ta lite tid att ladda ner den.
Formatbeskrivning:
Den här filen innehåller en komprimerad (eller zippad) uppsättning filer. Hämta filen till en mapp på hårddisken och kör sedan filen (dubbelklicka på den) för att packa upp filerna. Följ anvisningarna för att slutföra installationen.
Verifiera kontrollsummans värde så att hämtningen genomförs korrekt.
MD5:
Inte tillgänglig
SHA1:
Inte tillgänglig
SHA-256:
Inte tillgänglig
Filformat: Extern versionsinformation
Filnamn: perc4dc-IA64-351S-A05.txt
Filstorlek: 5.69 KB
Det här är en stor fil. Beroende på din anslutningshastighet kan det ta lite tid att ladda ner den.
Formatbeskrivning:
Det här filformatet innehåller oformaterad text som kan visas med en vanlig textredigerare.
Verifiera kontrollsummans värde så att hämtningen genomförs korrekt.
MD5:
Inte tillgänglig
SHA1:
Inte tillgänglig
SHA-256:
Inte tillgänglig
I och med att du hämtar accepterar du villkoren i Dells licensavtal för programvara. (på Engelska)
Operativsystem som stöds
Red Hat® Enterprise Linux 3
Red Hat® Enterprise Linux 4
Windows Server 2003
Gäller
PERC 4/DC
Installationsanvisningar
Instructions for R101840.EXE
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package
2. Click Continue.
3. Specify the location to unzip the files.
4. Click on the OK button to extract files.
After the files are extracted the message all files were successfully unzipped will appear.
5. Click the OK button to exit from the installer.
Installation
To update the firmware for your PERC 4/DC adapter, perform the following steps:
1. Extract the contents of the firmware package to your hardrive.
2. Copy the contents of the package to a formatted floppy disk, USB key, or CD-ROM.
3. Power on the server. From the EFI Boot Manager Menu, select EFI Shell.
4. Insert the media which contains the firmware update files from step 2.
This may be a USB key, floppy diskette (a USB floppy drive may be used), or CD-ROM.
5. At the Shell> prompt, type 'map -r' to view all mounted devices. Locate the device which contains the firmware update files - it will be enumerated as fs0, fs1, ect.
6. To change to the proper device, type 'fs1:'
NOTE: Your device may have a different file system number.
7. From the fs1:> prompt type 'percupd.nsh' to initiate the firmware update.
8. Follow the instructions from the EFI update tool to complete the firmware upgrade.
9. You will need to restart your system for the new firmware to take effect.
Custom Instructions for perc4dc-IA64-351S-A05.txt:
Download the readme file to view information about this release.
Download
1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Extract Files
1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package
2. Click Continue.
3. Specify the location to unzip the files.
4. Click on the OK button to extract files.
After the files are extracted the message all files were successfully unzipped will appear.
5. Click the OK button to exit from the installer.
Installation
To update the firmware for your PERC 4/DC adapter, perform the following steps:
1. Extract the contents of the firmware package to your hardrive.
2. Copy the contents of the package to a formatted floppy disk, USB key, or CD-ROM.
3. Power on the server. From the EFI Boot Manager Menu, select EFI Shell.
4. Insert the media which contains the firmware update files from step 2.
This may be a USB key, floppy diskette (a USB floppy drive may be used), or CD-ROM.
5. At the Shell> prompt, type 'map -r' to view all mounted devices. Locate the device which contains the firmware update files - it will be enumerated as fs0, fs1, ect.
6. To change to the proper device, type 'fs1:'
NOTE: Your device may have a different file system number.
7. From the fs1:> prompt type 'percupd.nsh' to initiate the firmware update.
8. Follow the instructions from the EFI update tool to complete the firmware upgrade.
9. You will need to restart your system for the new firmware to take effect.
Custom Instructions for perc4dc-IA64-351S-A05.txt:
Download the readme file to view information about this release.
Hjälp och självstudiekurser för drivrutiner
Fler hämtningar finns på Drivrutiner och hämtningsbara filer. Mer information om hur du använder sidan finns i Hjälp och anvisningar för drivrutiner