Dell PowerVault 224F/660F SES Firmware, v. 1.9.5, A01
AUTOMATISKT INSTALLERADDen här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
SES 1.9.5 Test Release Notes
The SES195.bin file is the required file for the download. It is highly recommended that all I/O is stopped before beginning this procedure.
You must update the SES firmware on each LS module in the PowerVault 660 and each of the attached enclosures. This includes the 660F as well as all attached 224F enclosures.
If you are replacing an LS module, or adding new PowerVault 224 units to an existing subsystem, you should update all LS modules with this firmware.
Enclosure services must be online to update the firmware. If enclosure services are offline then restore them to the online state before performing the following procedure.
Rekommenderat
Hitta den bästa nerladdningen för ditt system
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt system
Sök efter support
Ange din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare.Visa mig hur
Inga resultat hittades. Vi kunde inte hitta något som matchade din sökning. Ändra din sökning och försök igen.
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om.Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
Improvements to SES 1.9.5 SES 1.9.5 enhances the communication between SES modules. In the past there were times when thresholds set on the master SES were not copied to the slave SES. In a failover scenario the slave would apply the old values, requiring that the user reset the new thresholds.
SES 1.9.5 enhances reporting so that when an LS module fails, Dell Open Manage Array Manager can report the problem. The LED for the LS module will, as in previous versions, still light when an LS module is in a failed state.
SES 1.9.5 now reports the correct model name of the system, either PV660 or PV224.
In SES 1.3b2, upper warning/critical for LS Module temperature sensors is 45C/55C and for power supply sensors is 55C/65C, which is incorrect. The correct settings are in SES 1.9.5 and are 35C/45C for the LS module temperature sensors and 45C/55C for the power supply.
Dell Technologies rekommenderar att du kontrollerar den här uppdateringen för att avgöra om den gäller ditt system. Uppdateringen innehåller ändringar som endast påverkar vissa konfigurationer eller ger nya funktioner som eventuellt kan gälla den aktuella miljön.
To update the LS module SES firmware, perform the following steps:
1. Start Array Manager on the host system by clicking Start-- Programs-- Dell OpenManage Applications-- Array Manager-- Array Manager Console.
2. Update the SES firmware on the PowerVault 660F.
a. Click Arrays-- PV660F SubSystem-- Physical Array.
b. Right-click the controller for the subsystem you wish to upgrade and choose Download-- SES Firmware.
c. Select all the enclosure check boxes and click Next.
d. Click Browse and locate the SES195.bin file. Click Next.
e. Click Finish and OK.
NOTE: This process takes about 8 to 9 minutes for each additional LS module in the storage array. If the firmware update does not complete successfully, repeat the process until it does. This issue is not a hardware problem, but a software-timing issue.
f. After download completes, right-click the PV660F subsystem in Array Manager and choose Rescan to update the properties information.
g. Right-click the enclosure in Array Manager, choose Properties, and verify that it is using SES firmware version 1.9.5. If it is not, repeat the download procedure.
h. Physically remove the primary LS module to cause failover.
i. Right-click the PV660F subsystem in Array Manager and choose Rescan to update the properties information.
j. Right-click the enclosure and choose Properties to verify its firmware level is also at version 1.9.5. If it is not, repeat the download procedure.
k. Replace the LS module that you removed. If you have multiple enclosures, you must verify the firmware level on every LS module in the subsystem, one at a time.