AUTOMATISKT INSTALLERADDen här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
Innehållet på den här sidan kan ha översatts automatiskt. Fyll i formuläret längst ned på sidan för att ge feedback.
Den här filen installerades automatiskt som en del av en ny uppdatering. Om du har problem kan du ladda ner och installera om den manuellt.
LS-120 Drive Firmare Utility
Rekommenderat
Hitta den bästa nerladdningen för ditt system
Ange din produktinformation för att se den senaste informationen om drivrutiner för ditt system
Sök efter support
Ange din Dell service tag eller modell
Vill du söka efter din produkt? Ange en produktidentifierare.Visa mig hur
Inga resultat hittades. Vi kunde inte hitta något som matchade din sökning. Ändra din sökning och försök igen.
Den här drivrutinen är inte kompatibel
Den här drivrutinen gäller inte för den valda produkten. Välj en annan produkt för att ange din produktinformation för den här drivrutinen igen eller gå till produktsupportsidan för att visa alla drivrutiner för en annan produkt.
Logga in på Windows som administratör för att använda automatisk skanning. Om du redan är inloggad som administratör och ser det här meddelandet ska du starta om.Ditt system hanteras av IT-administratören och funktionerna kan vara begränsade.
Hitta fler uppdateringar. Använd SupportAssist för att hitta alla de senaste drivrutinsuppdateringarna för din enhet.
Korrigeringar och förbättringar
This utility updates the firmware on the LS-120 Drive, DP/N 042YKW, used on the Dell PowerEdge 7150 platform. It must be run from the EFI shell.
Dell Technologies rekommenderar att du kontrollerar den här uppdateringen för att avgöra om den gäller ditt system. Uppdateringen innehåller ändringar som endast påverkar vissa konfigurationer eller ger nya funktioner som eventuellt kan gälla den aktuella miljön.
Filformat:En eller flera självuppackande diskimageuppsättningar inuti en självuppackande ZIP-fil
Filnamn:B6T70600.exe
Filstorlek:493.5 KB
Det här är en stor fil. Beroende på din anslutningshastighet kan det ta lite tid att ladda ner den.
Formatbeskrivning:
Den här filen innehåller en komprimerad (eller zippad) uppsättning filer. Hämta filen till en mapp på hårddisken och dubbelklicka sedan på den för att packa upp filerna. Följ anvisningarna för att slutföra installationen.
1. Get 1 blank, formatted floppy disks. 2. Click the new icon on the desktop. The Self-Extractor window appears. 3. Click Setup. An MS-DOS window appears with a message indicating that you need 1 floppy diskettes. 4. Press the [ENTER] key. A message appears prompting you to insert a blank floppy diskette. Insert a floppy disk into the floppy disk drive. 5. Press the [ENTER] key. A message appears indicating that all data on the disk will be erased. 6. Press the [y] key and then press the [ENTER] key. The files are copied to the floppy diskette. Once the files have been copied to the diskette a message appears prompting you to insert the second diskette. 7. Repeat steps 4 – 6 until you reach the end of the diskette set. 8. After all the files have been copied to the last floppy disk, press the [ENTER] key and the MS-DOS window closes.
The unpack utility is DOS based. Run the executable file on a Windows based machine (not IA64), the following files will be unpacked and copied to a standard 1.44MB formatted floppy.
Place the floppy in the Ls-120 drive and Boot to the EFI Boot Manager Screen Select the EFI Boot option Should see the Device mapping table Look for the FS#'s to identify the Floppy, CDROM, and Hard Drives The LS-120 will have a description of Primary Master or Device 00. The Hard Drive will have a description of Scsi or Device 80. The command "map –r" will remap the devices. If the Device 80 or Scsi is FS1 then type: "FS1:" to change to the hard drive. Type: "dir" to print a directory to the screen. This is the main directory where the files should be copied. Should also see the dellup Directory. Copy the five files to the hard drive, (verify fs0 corresponds to the floppy drive) type: "copy fs0:auto.prm" the response should be fs0:\auto.prm -> fs1:\auto.prm[ok]
Type: "update" the utility will begin the following should appear on the screen.
Beginning Update Process New revision (file): C936M924 Old revision (ROM): C932M923
Note: If the Old revision number does not appear here then this drive cannot be updated !
Continue with the update of the Flash-EEPROM? (y/n) Type: "y"
Loader F/W Revision: 101 Erase Processing Erase OK Write Processing Write OK Flash Load: OK
The flash has completed and you are then returned to the EFI Prompt.