LSI Logic PERC 4/Di, v.1.18c, A03

OTOMATİK OLARAK YÜKLENDİ Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Önerilen

Sisteminize en uygun indirmeyi bulun

Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girin

Destek kaynaklarında ara

Dell Servis Etiketinizi veya modelinizi girin

Ürününüzü aramak mı istiyorsunuz? Bir ürün tanımlayıcısı girin. Nasıl yapılacağını göster

Bu sürücü uyumlu değil

Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.

Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.

Fixes & Enhancements

Not Applicable
Read More

Version

1.18c, A03

Sürüm tarihi

13 Ağu 2002

İndirme Türü

Driver

Kategori

SCSI RAID

Önem

Optional
Dell Technologies, sisteminiz için geçerli olup olmadığını belirlemek için bu güncellemeyi incelemenizi önerir. Bu güncelleme, yalnızca belirli yapılandırmaları etkileyen değişiklikler içerir veya ortamınız için geçerli olabilecek ya da olmayabilecek yeni özellikler sağlar.
Kullanılabilir biçimler

Dosya Biçimi: Dosyaları doğrudan yerel diske ayıklar
Dosya Adı: perc4di-118c-72c.tar.gz
Dosya Boyutu: 538.62 KB
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.
İndirme işleminizin bütünlüğünü sağlamak için lütfen sağlama toplamı değerini doğrulayın.
MD5:
Not available
SHA1:
Not available
SHA-256:
Not available

İndirdiğinizde, Dell Software Lisans Sözleşmesi’nin koşullarını kabul etmiş olursunuz.

Instructions for downloading and creating driver diskette:
----------------------------------------------------------

You will need a formatted 3 1/2 inch floppy diskette for the following procedure.

Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.

Extract the file to the floppy disk as follows:

1. On a Linux system:

Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy
tar xvzf -C /mnt/floppy
(Eg: /temp/PERC4di-118c-72c.tar.gz)
umount /mnt/floppy

2. On a Microsoft Windows system:

You can use Winzip to extract tar.gz archives. However,
note the following settings under Winzip to ensure correct
extraction of the files.

Start Winzip -> Go to Options -> Configuration

Under the Miscellaneous tab make sure "TAR file smart
CR/LF conversion" is unchecked.

Upon opening the tar.gz archive with Winzip, you get the
following prompt:

'Archive contains one file. Should Winzip decompress it to
a temporary folder and open it?'

Press 'yes' and extract the files normally under Winzip to
the floppy drive.



Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller
-------------------------------------------------------

There are two ways of installing Red Hat 7.2 driver onto the
PERC 4/Di as a boot controller. One is using a driver disk during
OS installation and the second is using a driver (megaraid) RPM to update
driver after OS is installed. The steps for both of these methods are
provided below. All the files needed for both methods are included in the
driver diskette created above.

For more detailed installation instructions of Red Hat 7.2, please refer
to the OS installation guide at http://www.dell.com/linux.


I. Installing driver during OS installation:
--------------------------------------------

1. Boot normally from the Redhat installation CD-Rom.

2. Type 'linux dd' on the boot prompt.

3. When the install prompts for a driver disk, insert the
driver diskette created above and press 'Enter'.

4. Installation progresses normally. Continue until the
'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a
shell window and type the following commands:

chroot /mnt/sysimage
cd /boot
/sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
lilo ( only if lilo was used as bootloader. If grub used - skip this step )
exit

Press CTRL-ALT-F7 to get back to the install screen.

5. Complete the installation as directed by the install.


II. Update driver using RPMs after OS is installed
--------------------------------------------------

Type the following commands under a Linux command shell:

mount /dev/fd0 /mnt/floppy
cd /mnt/floppy
./megarpmwrapper.sh

Than follow the on-screen instructions to install the RPM driver.

For more detailed information about the script megarpmwrapper.sh,
please refer to the release_notes.txt included in the release.

Sürücülerle ilgili yardım ve öğreticiler