Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
OTOMATİK OLARAK YÜKLENDİBu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Seagate drives not seen during SMTD installation or after adding additional drives online in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Önerilen
Sisteminize en uygun indirmeyi bulun
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girin
No results found.We couldn't find anything for your search. Please modify your search and try again.
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın.Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms: A) During an install from System Management Tool and Documentation DVD: 1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup. 2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install: The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Dell Technologies, bir sonraki zamanlanmış güncelleme döngünüzde bu güncellemeyi uygulamanızı önerir. Bu güncelleme, genel sistem durumunu korumaya yönelik değişiklikler içerir. Sistem yazılımının güncel ve diğer sistem modülleriyle (bellenim, BIOS, sürücüler ve yazılım) uyumlu kalmasını sağlar ve başka yeni özellikleri içerebilir.
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, and then run (double-click) it to unzip the set of files. Follow the instructions to complete the installation.
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Detailed Instructions
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.