OTOMATİK OLARAK YÜKLENDİBu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
This software contains the Windows NT4 driver for the DELL PERC 2, PERC 2/Si, PERC 3/Si, and PERC 3/Di controllers.
Önerilen
Sisteminize en uygun indirmeyi bulun
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girin
No results found.We couldn't find anything for your search. Please modify your search and try again.
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın.Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
Fixes/Enhancements ==================
-Filter driver checks Dispatch_Level before calling KeWaitForSingleObject avoid bugcheck 0xB8 -Modified unknown AIF handling to prevent Driver Verifier hang. -STATUS_INVALID_PARAMETER returned for requests with: Zero-length input buffer size.Invalid input buffer size, i.e. not the size of the expected structure. Invalid memory address for the input buffer.A null input buffer. -Deletes perc2hib reference in lower filter list rather than entire filter list via inf. -Corrected a major entry-point in the filter driver that Windows uses for major Plug-N-Play requests (IRP_MJ_PNP). This entry point was incorrectly passing the request to the next lower device in the device stack. -Deleted the section that removes the upper and lower filters. This section caused errors to be logged in the setupapi.log in Windows. -Added support for new vSCSI implementation
Dell Technologies, bir sonraki zamanlanmış güncelleme döngünüzde bu güncellemeyi uygulamanızı önerir. Bu güncelleme, genel sistem durumunu korumaya yönelik değişiklikler içerir. Sistem yazılımının güncel ve diğer sistem modülleriyle (bellenim, BIOS, sürücüler ve yazılım) uyumlu kalmasını sağlar ve başka yeni özellikleri içerebilir.
Dosya Biçimi:Dosyaları doğrudan yerel diske ayıklar
Dosya Adı:nta12drv.exe
Dosya Boyutu:167.08 KB
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.
This software code release requires all V2.8 components: firmware, device driver and management utilities. Using some components from previous releases may cause some unknown errors.
Driver Installation for Windows NT 4.0 ==============================================
To perform a fresh installation of the Windows NT device drivers for the controller, follow these steps:
1. Boot the system using the Windows NT 4.0 CD.
2. When the message: "Setup is inspecting your computer's hardware configuration" appears, press F6 immediately.
3. The Windows NT 4.0 Setup screen will appear, requesting input for additional adapters in the system. Press 'S' to specify an additional adapter.
4. A selection menu will appear. Scroll to "Other" and hit ENTER.
5. Insert the driver diskette and press ENTER when prompted.
6. The selection: "DELL PERC 2, 2/Si, 3/Si, 3/Di RAID CONTROLLERS" will appear, hit ENTER.
7. After the driver has loaded, press ENTER to continue the installation.
NOTE: Before you perform the upgrade, uninstall the Controller Management Software (FAST and the CLI). See the installation guide associated with your controller for instructions on how to uninstall the Controller Management Software.
To upgrade the Windows NT device drivers for the controller, follow these steps: 1. Follow this path from Start:
3. The system displays an "Install Driver" window. Select "Have Disk".
4. The system displays an "Install From Disk" window. The "Install Driver" window instructs you to insert the manufacturer's installation media into the drive and click < Ok>. In this case, insert the diskette that contains the NT device drivers for your controller
5. Enter the drive and location of the files. The default location on the diskette that contains the NT device drivers is: "a:\".
The system displays a message identifying the controller for which you want to upgrade the Windows NT device drivers. The message requests that you click the button.
6. The system displays "System Settings Change" and asks if you want to restart the computer. Press YES.