Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.
Before updating, please read the installation instructions and important information noted below.
Dell Server System BIOS, A06
OTOMATİK OLARAK YÜKLENDİBu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.
900 MHz B0 Stepping BIOS for PE8450.
Önerilen
Sisteminize en uygun indirmeyi bulun
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girin
No results found.We couldn't find anything for your search. Please modify your search and try again.
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın.Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
BIOS Release A06 contains B0 microcode to support 900MHz processors on PE8450.
Dell Technologies, sisteminiz için geçerli olup olmadığını belirlemek için bu güncellemeyi incelemenizi önerir. Bu güncelleme, yalnızca belirli yapılandırmaları etkileyen değişiklikler içerir veya ortamınız için geçerli olabilecek ya da olmayabilecek yeni özellikler sağlar.
Dosya Biçimi:Dosyaları doğrudan yerel diske ayıklar
Dosya Adı:B6899R06.exe
Dosya Boyutu:738.85 KB
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.
This utility must be executed in a system without memory managers installed. If EMM386, QEMM, 386MAX, or Windows is active, then the FLASH update is not safe. Remove any memory manager or exit Windows before executing the FLASH Memory Update Utility.
I. BIOS Update ---------------
To update the BIOS, do the following:
1. Note the settings of the SETUP parameters. Enter SETUP by hitting the F2 key during boot up. Write down the settings for each of parameters. At the end of the BIOS update process you should set the parameters to default values by hitting the F9 key, and then re-enter these values you have written down.
2. Insert the BIOS Update Diskette into drive A:.
3. Reset the system.
4. System boots the BIOS Update Diskette.
5. Choose option 1 to update the BIOS.
6. System will automatically reboot once the BIOS update is completed. Please remove the floppy diskette from drive A:.
7. Check to make sure the BIOS version is the new version as the system reboots.
8. Enter Setup by pressing the F2 key during boot up. Once in Setup, press the F9 to set the parameters back to default values. Re-enter the values you wrote down at the beginning of this process. If you do not set the CMOS values back to defaults using the F9 key, the system may function erratically.
II. BIOS Recovery ------------------
To recover the BIOS from a corrupted Flash or bad BIOS update, do the following:
1. Turn system power off.
2. Move the BIOS recovery Switch number 2 to the recovery (ON) position.
3. Insert the BIOS recovery diskette containing the latest BIOS files including user binary file.
4. Turn system power on.
5. At this point, the system boots from the DOS-bootable recovery diskette without video display. BIOS emit one beep when it passes control to DOS. DOS then execute a AUTOEXEC.BAT that contains IFLASH.EXE. It emits one high pitched beep to indicate the beginning of the flash operation. After it recovers system BIOS, it emits two high pitched beeps. Then it recovers user binary code. It emits two high pitched beeps to indicate the recovery completed successfully. If the recovery fails, it emits a continuous series of beeps. The entire process takes between three to five minutes.
6. Turn system power off.
7. Remove the recovery diskette.
8. Restore the switch to the original position.
9. Turn system power on for normal operation.
Note: you may encounter a CMOS Checksum error or other problem after reboot. Try shutting down the system and booting up again. CMOS checksum errors require that you enter Setup, check your settings, save your settings, and exit Setup.
Need help with BIOS issues?
Find a solution in Dell's BIOS troubleshooting and usage guide.