Adaptec 39160 SCSI Controller - Firmware, v.BIOS v3.10, A03
OTOMATİK OLARAK YÜKLENDİ Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.Bu sayfa içeriği otomatik olarak çevrilmiş olabilir. Geri bildirim sağlamak için sayfanın en altındaki formu doldurun.
Adaptec 39160 SCSI Controller BIOS
Önerilen
Sisteminize en uygun indirmeyi bulun
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girinDestek kaynaklarında ara
Dell Servis Etiketinizi veya modelinizi girin
Ürününüzü aramak mı istiyorsunuz? Bir ürün tanımlayıcısı girin. Nasıl yapılacağını göster
Bu sürücü uyumlu değil
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Otomatik taramayı kullanmak için Windows'da yönetici olarak oturum açın. Zaten yönetici olarak oturum açtıysanız ve bu mesajı görüyorsanız lütfen yeniden başlatın. Sisteminiz BT yöneticiniz tarafından yönetiliyor ve özellikler sınırlı olabilir.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
Includes all fixes and enhancements in Dell Special code stream and Adaptec Service Pack code
stream (listed below):
3.0
New Features:
-Single Image
-Supports Int 13h extension : check extension present, AH=30h
-Supports SCSI pass through; Int 13h AH=50h
-PnP header table limit is obtained from system BIOS that support the function "Get Device Count".
- key to toggle color/monochrome video display mode will be removed
-In the Host Adapter Configuration screen, the 'SCSI Termination Level' information will be
removed
-In the Boot Device configuration screen, the 'Select SCSI Peripheral from which to boot' option
will not be available to the systems that support BIOS Boot Specification (BBS).
-In the Boot Device Configuration screen, another option will be added to configure the master
channel for the single image feature; for the Ultra160 dual channel chip, either function can be the master
-In the Advance Configuration Options screen, POST display mode will support silent, normal and
diagnostics menu
-In the Advance Configuration Options screen, 'BIOS support Int 13h extension' will be removed
-In the Disk Utilities screen, the device capacity will displayed up to XXX GB
-In the Disk Utilities screen, the format progress will be displayed if the drive does support
progress status bytes in the sense key
3.10
New Features:
-EFI legacy compliance
Bugs Fixed:
- More robust PnP checking
- El Torito AH=4Ch, Initiate disk emulation and boot
- Allocate EBDA as needed during runtime INT 13h calls
- Fresh installation hangs on Win2k due to conflict with CHIM code
- Display capacity for SAFTE
Read Morestream (listed below):
3.0
New Features:
-Single Image
-Supports Int 13h extension : check extension present, AH=30h
-Supports SCSI pass through; Int 13h AH=50h
-PnP header table limit is obtained from system BIOS that support the function "Get Device Count".
-
-In the Host Adapter Configuration screen, the 'SCSI Termination Level' information will be
removed
-In the Boot Device configuration screen, the 'Select SCSI Peripheral from which to boot' option
will not be available to the systems that support BIOS Boot Specification (BBS).
-In the Boot Device Configuration screen, another option will be added to configure the master
channel for the single image feature; for the Ultra160 dual channel chip, either function can be the master
-In the Advance Configuration Options screen, POST display mode will support silent, normal and
diagnostics menu
-In the Advance Configuration Options screen, 'BIOS support Int 13h extension' will be removed
-In the Disk Utilities screen, the device capacity will displayed up to XXX GB
-In the Disk Utilities screen, the format progress will be displayed if the drive does support
progress status bytes in the sense key
3.10
New Features:
-EFI legacy compliance
Bugs Fixed:
- More robust PnP checking
- El Torito AH=4Ch, Initiate disk emulation and boot
- Allocate EBDA as needed during runtime INT 13h calls
- Fresh installation hangs on Win2k due to conflict with CHIM code
- Display capacity for SAFTE
Version
BIOS v3.10, A03
Sürüm tarihi
06 Eki 2004
İndirme Türü
Sistem BIOS
Kategori
SCSI non-RAID
Önem
ÖnerilenDell Technologies, bir sonraki zamanlanmış güncelleme döngünüzde bu güncellemeyi uygulamanızı önerir. Bu güncelleme, genel sistem durumunu korumaya yönelik değişiklikler içerir. Sistem yazılımının güncel ve diğer sistem modülleriyle (bellenim, BIOS, sürücüler ve yazılım) uyumlu kalmasını sağlar ve başka yeni özellikleri içerebilir.
Kullanılabilir biçimler View Important Information
Dosya Biçimi: One or more self extracting disk images inside of a self extracting zip
Dosya Adı: 160FW310.exe
Dosya Boyutu: 293.19 KB
Bu büyük bir dosyadır. Bağlantı hızınıza bağlı olarak indirme işlemi biraz zaman alabilir.
Biçim Açıklaması:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, then double-click it to unzip the set of files. Follow the instructions to complete the installation.
İndirme işleminizin bütünlüğünü sağlamak için lütfen sağlama toplamı değerini doğrulayın.
MD5:
Not available
SHA1:
Not available
SHA-256:
Not available
İndirdiğinizde, Dell Software Lisans Sözleşmesi’nin koşullarını kabul etmiş olursunuz.
Important Information
In order to create this diskette, the file must be downloaded to and executed on a system running
Microsoft Windows.
*NOTE: If the 39160 HBA is NOT the boot controller in your system, it is highly recommended to disable INT13h support (done in the SCSISelect boot time utility - invoked by pressing 'Ctl-A' when prompted to do so during POST) for the 39160 adapter, since this could impact interoperation with the boot controller.
Microsoft Windows.
*NOTE: If the 39160 HBA is NOT the boot controller in your system, it is highly recommended to disable INT13h support (done in the SCSISelect boot time utility - invoked by pressing 'Ctl-A' when prompted to do so during POST) for the 39160 adapter, since this could impact interoperation with the boot controller.
Desteklenen İşletim Sistemleri
Geçerli Değil
Şunlar için geçerlidir:
39160 SCSI Controller - Firmware
Kurulum talimatları
Custom Instructions for 160FW310.exe:
NOTE: For PV725N users, please refer to the online documentation "Upgrading your 39160 SCSI card firmware" available in the PV725N User Guides section of http://support.dell.com
Floppy Disk Boot to Disk for 160FW310.exe
Download
IMPORTANT NOTE: For Netware & Linux Users, this diskette creation
file must be downloaded to and executed on a system running Microsoft
Windows 9x or above in order to create the bootable floppy disk.
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click
Yes, I Accept this Agreement.
3. When the File Download window appears, click Save
(Windows XP users will click Save) this program to disk and click OK. The
Save In: window appears.
4. From the Save In: field, click the down arrow then click to
select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close.
The file icon appears on your desktop.
Hard Drive Floppy Disk Creation
1. Get 1 blank, formatted floppy disk.
2. Double-click the new icon (it looks like a floppy diskette) on
the desktop. The Self-Extractor window appears.
3. Click Setup. A black MS-DOS window appears with a
message indicating that you need 1 floppy diskette.
4. Press the [ENTER] key.
A message appears prompting you to insert a blank floppy diskette.
Insert a floppy disk into the floppy disk drive.
5. Press the [ENTER] key. A message appears indicating that
all data on the disk will be erased.
6. Press the [y] key and then press the [ENTER] key.
The files are copied to the floppy diskette.
7. After all the files have been copied to the floppy disk,
press the [ENTER] key and the MS-DOS window closes.
Install
1. Insert the newly created floppy disk into the Floppy
drive of the system to be upgraded.
2. Reboot your system.
3. Once system has booted to diskette, follow instructions as
they appear on the system console. They will guide you through the
update process, including the subsequent reboots needed to clear the
card of legacy image information. Refer to README.TXT file for more
information.
NOTE: For PV725N users, please refer to the online documentation "Upgrading your 39160 SCSI card firmware" available in the PV725N User Guides section of http://support.dell.com
Floppy Disk Boot to Disk for 160FW310.exe
Download
IMPORTANT NOTE: For Netware & Linux Users, this diskette creation
file must be downloaded to and executed on a system running Microsoft
Windows 9x or above in order to create the bootable floppy disk.
1. Click Download Now, to download the file.
2. If the Export Compliance Disclaimer window appears, click
Yes, I Accept this Agreement.
3. When the File Download window appears, click Save
(Windows XP users will click Save) this program to disk and click OK. The
Save In: window appears.
4. From the Save In: field, click the down arrow then click to
select Desktop and click Save. The file will download to your desktop.
5. If the Download Complete window appears, click Close.
The file icon appears on your desktop.
Hard Drive Floppy Disk Creation
1. Get 1 blank, formatted floppy disk.
2. Double-click the new icon (it looks like a floppy diskette) on
the desktop. The Self-Extractor window appears.
3. Click Setup. A black MS-DOS window appears with a
message indicating that you need 1 floppy diskette.
4. Press the [ENTER] key.
A message appears prompting you to insert a blank floppy diskette.
Insert a floppy disk into the floppy disk drive.
5. Press the [ENTER] key. A message appears indicating that
all data on the disk will be erased.
6. Press the [y] key and then press the [ENTER] key.
The files are copied to the floppy diskette.
7. After all the files have been copied to the floppy disk,
press the [ENTER] key and the MS-DOS window closes.
Install
1. Insert the newly created floppy disk into the Floppy
drive of the system to be upgraded.
2. Reboot your system.
3. Once system has booted to diskette, follow instructions as
they appear on the system console. They will guide you through the
update process, including the subsequent reboots needed to clear the
card of legacy image information. Refer to README.TXT file for more
information.
Sürücülerle ilgili yardım ve öğreticiler
Daha fazla indirme için bkz. Sürücüler ve indirmeler. Bu sayfadaki bilgileri kullanmayla ilgili yardım almak için lütfen Sürücü Yardımı ve Öğretici Videoları bölümünü ziyaret edin.