Driver Details

Dell OptiPlex System BIOS, A06

Optiplex GX50 A06 FlashBIOS

Version

Version A06, A06

Compatibility

Systems
Operating Systems
  • BIOS

Applies to

�;

Date

Release date
8/20/2002
Last Updated
11/3/2011

Importance

Optional. Dell recommends the customer review specifics about the update to determine if it applies to your system. The update contains changes that impact only certain configurations, or provides new features that may/may not apply to your environment.

Available formats

File Format:Floppy
File Name:BGX50_06.exe
Download Type:HTTP
File Size: 490KB
Format DescriptionThis file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, then double-click it to unzip the set of files. Follow the instructions to complete the installation.
Added to download list
Go to [{0}]
To ensure the integrity of your download, please verify the checksum value.
MD5:
Not available
SHA1:
Not available
SHA-256:
Not available

File Format:Non-Packaged
File Name:GX50_A06.EXE
Download Type:HTTP
File Size: 316KB
Format DescriptionThis file format consists of a BIOS-executable file. To use it, download the file and copy it to a DOS-bootable USB flash drive, then boot the system to the USB flash drive and run the program.
Added to download list
Go to [{0}]
To ensure the integrity of your download, please verify the checksum value.
MD5:
Not available
SHA1:
Not available
SHA-256:
Not available

By downloading, you accept the terms of the Dell Software License Agreement.


Fixes & Enhancements

The following changes have been made to the A04 to create A06 (A05 was not
released from Development):
* Adjusted USB Emulation support for special keys, and non-US keyboards.
* Added IDE UDMA support to speed up resume from Hibernate (when enabled).
* Added support for new Processors.
* Added support for additional models in the GX50 Series.
* Reduce POST time when no PS/2 keyboard or Mouse installed.
* Fixed issues with some USB devices causing a keyboard POST error with a
USB keyboard.
* Added two new diagnostic LED codes for better memory failure isolation.
No Memory Detected (ABCD=Grn, Yel, Yel, Yel)
Memory Configuration Failure (ABCD=Grn, Yel, Grn, Yel)
* Fixed false error on Floppy Drive when running Diags From Bootable Diags
CD without a Floppy Drive.

* Fixed possible CMOS corruption when adjusting system configuration
through Open Manage.

* Allow Num-pad Enter key on boot menu screen.

* Changed the AC Power Recovery to OFF as default.

* Added "Low Power Mode" option to System Setup.

* Fixed issue with UNKNOWN devices in System Setup for IDE devices.
If a failure occurs, now check the second IDE cable for devices.

* Fixed hang problem with Creative Audigy and large sound samples.

* Fixed issue when resuming from Hibernate with keyboard & mouse swapped.

Installation instructions



Default Instructions for GX50_A06.EXE:

Non-Packaged
Creating the disk:
NOTE: This procedure requires one blank bootable, formatted 3.5-inch
floppy disk; label the disk BIOS.

1. When the File Download window appears, click “Save this program to
disk”.
2. Choose “Desktop” as the location.
3. Click “Ok”.
4. After the file has finished copying files, click “Close”.
5. Press the “Windows” + “M” keys at the same time to minimize all
the open windows.
6. Insert the blank bootable formatted 3.5-inch floppy disk.
7. Right-click the copy of the file, point to “Send To”, click “3 1/2
Floppy (a)”, and then skip to the section Flashing the BIOS below.

Flashing the BIOS:
NOTICE: Changing the system BIOS may result in unintended side affects,
such as incompatibility of the new BIOS with installed hardware. If
problems arise after a BIOS change, it may be necessary to return the
system to the original version of the BIOS.
1. If you are flashing the BIOS on a portable computer, be sure that
the AC adapter is plugged in and the computer is not operating on battery
power.
2. Ensure that the Flash BIOS disk is inserted into the floppy disk
drive.
3. Click the “Start” button, click “Shut Down”, click “Restart”, and
then click “Ok”.
The computer should restart and boot to the floppy disk.

NOTE: If the flash BIOS program does not start, and you see only an A:\
prompt, refer to the instructions from the Dell File Library page for the
BIOS update or to the Readme.txt instructions. Generally, you will type
the name of the executable flash BIOS file such as BGX1_A10.exe for BIOS
version A10 on the OptiPlex™ series system.

A Press any key to continue prompt appears.
4. Press the “Enter” key.
A Press Y to replace old BIOS with new BIOS prompt appears.
5. Press the “Y” key.

NOTICE: Do not interrupt the system during this process. Please refrain
from pressing any keys on the keyboard, moving the mouse, or interrupting
power to the system. Failure to do so could result in damage to the system
BIOS.

When the computer has finished updating the BIOS, a Flash program
successful. Press any key to reboot prompt appears.
6. Remove the floppy disk and press the “Enter” key.
7. The computer will now restart with the new revision of the BIOS
installed.
The boot screen will indicate the BIOS version.

If you encounter device or resource errors after flashing the system BIOS,
enter the System Setup, clear the NVRAM and restore the system defaults.
For more information, refer to Dell Knowledge Base Articles:
· FA1035264 Title "How do I restore setup defaults on my Dell
OptiPlex system?"
· FA1035227 Title "How do I clear NVRAM on my Dell OptiPlex system?"



Floppy Disk Boot to Disk for BGX50_06.exe

Download

1. Click Download Now, to download the file.
2. When the File Download window appears, click Save (Windows XP users will click Save) this program to disk and click OK. The Save In:
window appears.
3. From the Save In: field, click the down arrow then click to
select Desktop and click Save. The file will download to your desktop.
4. If the Download Complete window appears, click Close. The file
icon appears on your desktop.

Hard Drive Floppy Disk Creation

1. Get 1 blank, formatted floppy disks.
2. Double-click the new icon (it looks like a floppy diskette) on
the desktop. The Self-Extractor window appears.
3. Click Setup. An black MS-DOS window appears with a message
indicating that you need 1 floppy diskettes.
4. Press the [ENTER] key.
A message appears prompting you to insert a blank floppy diskette.
5. Insert a floppy disk into the floppy disk drive.
6. Press the [ENTER] key. A message appears indicating that all
data on the disk will be erased.
7. Press the [y] key and then press the [ENTER] key.
The files are copied to

My Download List-#1 (0 )

Drivers help and tutorials

My download lists

My download lists enables you to create and save lists of drivers to install at a later time. Lists can only be saved by logging into your existing account or creating a new one, and selecting “Save this list.”
Learn more