- Notes, Cautions, and Warnings
- Introduction
- AMP Event Messages
- ASR Event Messages
- BAR Event Messages
- BAT Event Messages
- BIOS Event Messages
- BOOT Event Messages
- CBL Event Messages
- CMC Event Messages
- CPU Event Messages
- CPUA Event Messages
- CTL Event Messages
- DH Event Messages
- DIAG Event Messages
- DIS Event Messages
- DKM Event Messages
- ECM Event Messages
- ENC Event Messages
- EPP Event Messages
- FAN Event Messages
- FC Event Messages
- FCD Event Messages
- FLDC Event Messages
- FSD Event Messages
- HWC Event Messages
- IOID Event Messages
- IOV Event Messages
- IPA Event Messages
- ISM Event Messages
- JCP Event Messages
- LC Event Messages
- LIC Event Messages
- LNK Event Messages
- LOG Event Messages
- MEM Event Messages
- NIC Event Messages
- OSD Event Messages
- OSE Event Messages
- PCI Event Messages
- PDR Event Messages
- PFM Event Messages
- POW Event Messages
- PR Event Messages
- PST Event Messages
- PSU Event Messages
- PSUA Event Messages
- PWR Event Messages
- RAC Event Messages
- RDU Event Messages
- RED Event Messages
- RFL Event Messages
- RFLA Event Messages
- RFM Event Messages
- RRDU Event Messages
- RSI Event Messages
- SEC Event Messages
- SEL Event Messages
- SSD Event Messages
- STOR Event Messages
- SUP Event Messages
- SWC Event Messages
- SWU Event Messages
- SYS Event Messages
- TMP Event Messages
- TMPS Event Messages
- TST Event Messages
- UEFI Event Messages
- USR Event Messages
- VDR Event Messages
- VF Event Messages
- VFL Event Messages
- VFLA Event Messages
- VLT Event Messages
- VME Event Messages
- VRM Event Messages
Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2
VFL Event Messages
VFL0001
- Message
- The vFlash SD Card operation is successful.
- Detailed Description
- The requested operation for the vFlash SD Card completed successfully.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0002
- Message
- Unable to query the vFlash media status.
- Detailed Description
- The status of vFlash SD Card or the vFlash media partition cannot be obtained, because some of the iDRAC services are busy.
- Recommended Response Action
- Retry the operation. If the issue persists, restart the iDRAC and retry the operation. If the issue continues to persist, contact your service provider.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0003
- Message
- Partition arg1 does not exist.
- Arguments
- arg1 = partition number
- Detailed Description
- The partition number identified in the message cannot be queried, because identified partition does not exist.
- Recommended Response Action
- Use a partition number of an existing partition for the requested operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0004
- Message
- Unable to perform the vFlash media operation.
- Detailed Description
- The requested vFlash media operation could not be performed, because some of the iDRAC services are busy.
- Recommended Response Action
- Retry the operation. If the issue persists, restart the iDRAC and retry the operation. If the issue continues to persist, contact your service provider.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0005
- Message
- No vFlash partitions exist.
- Detailed Description
- There are no vFlash partitions available currently for the display.
- Recommended Response Action
- No response action is required.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0007
- Message
- No vFlash SD card is present.
- Detailed Description
- The operations could not be completed because a vFlash SD Card is not detected.
- Recommended Response Action
- Confirm an SD Card is present in the vFlash SD Card reader slot. Otherwise, insert an SD Card and retry the operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0009
- Message
- vFlash media is currently in use by another operation.
- Detailed Description
- Unable to access the vFlash media, because another operation is currently using the vFlash media.
- Recommended Response Action
- Wait until the vFlash media is available for the requested operation, and then retry the operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
VFL0010
- Message
- An operation is in progress on the SD card.
- Detailed Description
- Another operation is currently in progress on the SD card.
- Recommended Response Action
- Wait untill the current operation is completed, and then retry the requested operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0011
- Message
- vFlash media is not disabled.
- Detailed Description
- The vFlash media is not disabled.
- Recommended Response Action
- Disable the vFlash media by running the command racadm set idrac.vFlashSD.Enable 0.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0012
- Message
- vFlash media is not enabled.
- Detailed Description
- The vFlash media is not enabled.
- Recommended Response Action
- Enable the vFlash media by running the command racadm set idrac.vFlashSD.Enable 1.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0013
- Message
- The vFlash SD Card is in read-only mode.
- Detailed Description
- The request could not be successfully completd, because the vFlash SD Card is in read-only mode. Write operations cannot be performed on the card.
- Recommended Response Action
- Change the access mode on the vFlash SD Card to read-write.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0014
- Message
- The vFlash SD card is not initialized.
- Detailed Description
- The vFlash SD card is not initialized. Either the card is not properly formatted or it may not be supported.
- Recommended Response Action
- Format the vFlash SD card by running the command "racadm vflashsd initialize". Make sure that the card is supported by contacting your service provider for a list of supported SD card types.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0015
- Message
- vFlash media partition is of read-only type.
- Detailed Description
- The request could not be successfully completd, because the vFlash SD Card partition is in read-only mode. Write operations cannot be performed on the card partition.
- Recommended Response Action
- Change the partition access type to read-write by running the command racadm set idrac.vFlashPartition.<index>.accesstype 1.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0016
- Message
- vFlash media partition is already in attached state.
- Detailed Description
- The requested vFash media partition is already attached to the host operating system.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0017
- Message
- Unable to perform the vFlash media operation because the vFlash media partition is corrupted.
- Detailed Description
- The file system on the specified vFlash media partition could not be recognized. Data on the partition may be corrupted.
- Recommended Response Action
- Format the vFlash SD Card using the racadm vflashsd initialize command and retry the operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0018
- Message
- The requested operation is in progress.
- Detailed Description
- The requested operation is currently in progress.
- Recommended Response Action
- Wait for the requested operation to complete.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0019
- Message
- The vFlash media partition is already in detached state.
- Detailed Description
- The requested vFlash media partition is already detached from the host operating system.
- Recommended Response Action
- No response action is required.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0020
- Message
- vFlash SD card is not ready.
- Detailed Description
- The vFlash SD card is currently in use by another operation.
- Recommended Response Action
- Wait for the current vFlash SD card operation to finish, and they retry.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0021
- Message
- One of the vFlash SD Card partitions is already attached to the host operating system.
- Detailed Description
- The requested operation cannot be performed if one of the vFlash SD cards is in an attached state.
- Recommended Response Action
- Detach the vFlash SD Card partitions by running the racadm command "racadm set iDRAC.vflashpartition.<partition number>.attachstate 0". and retry the operation.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
VFL0705
- Message
- Error occurred and SD card could not be initialized.
- Detailed Description
- An error has occurred while initializing the SD card. The SD card is not present or vFlash is not enabled, or the SD card is write-protected.
- Recommended Response Action
- Re-insert the SD card, enable the SD card, or disable write-protection on the SD card. Then try to initialize the SD card again.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0711
- Message
- SD card is write-protected and could not be initialized.
- Detailed Description
- An error occurred while initializing the SD card because the SD card write-protection feature is enabled.
- Recommended Response Action
- Move the SD card write-protection tab to the disabled position and try again.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0712
- Message
- One or more partitions are busy with another operation; the SD card could not be initialized.
- Detailed Description
- none
- Recommended Response Action
- Retry the task after a few minutes
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0713
- Message
- One or more partitions are currently attached; the SD card could not be initialized.
- Detailed Description
- none
- Recommended Response Action
- Detach the partitions and try again.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0715
- Message
- Error occurred while initializing the SD Card due to insufficient permission.
- Detailed Description
- None
- Recommended Response Action
- Contact the administrator for the required permissions and try again.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0716
- Message
- SD Card is not a vFlash SD Card; the SD card could not be initialized.
- Detailed Description
- An error has occurred while initializing SD Card because the SD card is not an approved vFlash SD card.
- Recommended Response Action
- Insert a vFlash SD card and try again.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0719
- Message
- One or more partitions are in use; the SD card could not be initialized.
- Detailed Description
- The SD card is in use by another process. Initialization requires exclusive access to the SD card to complete the initialization.
- Recommended Response Action
- The SD card is in use by another process. Retry after a few minutes.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL0721
- Message
- Error occurred while initializing the SD Card due to a timeout.
- Detailed Description
- The SD card Initilization did not complete within the maximum process alloted time.
- Recommended Response Action
- Retry after a few minutes.
- Category
- Configuration (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
VFL1001
VFL1003
- Message
- Removable Flash Media arg1 is not IPMI-function ready.
- Arguments
- arg1 = name
- Detailed Description
- The removable flash media is installed but improperly configured or failed to initialize.
- Recommended Response Action
- If unintended, reinstall the flash media and module.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 2 (Warning)
VFL1005
- Message
- Removable Flash Media arg1 is not ready.
- Arguments
- arg1 = name
- Detailed Description
- The media is being prepared or is under maintenance. If the problem persists, reinstall the card.
- Recommended Response Action
- Please wait for the media to be ready.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 2 (Warning)
VFL1006
- Message
- Removable Flash Media arg1 is offline.
- Arguments
- arg1 = name
- Detailed Description
- At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress.
- Recommended Response Action
- If unintended, reinstall the flash media.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 2 (Warning)
VFL1008
- Message
- Failure detected on Removable Flash Media arg1 .
- Arguments
- arg1 = name
- Detailed Description
- An error is reported during a SD card read or write.
- Recommended Response Action
- Re-install the flash media, if the issue persists replace the media.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2505
- LCD Message
- Removable Flash Media <name> failed. Check SD Card
VFL1009
VFL1010
VFL1011
VFL1014
- Message
- Removable Flash Media arg1 is write protected.
- Arguments
- arg1 = name
- Detailed Description
- The card is write-protected by the physical latch on the SD card. IDSDM cannot use a write-protected card.
- Recommended Response Action
- if unintended, remove the media and disable write protection.
- Category
- System Health (VFL = vFlash Event)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2506
- LCD Message
- Removable Flash Media <name> is write protected. Check SD Card
VFL1015
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\