- Notes, Cautions, and Warnings
- Installation
Instructions And Important Information
- Overview
- Latest available operating system
- System configuration requirements
- Reviewing preconfiguration options
- Installing and
reinstalling your operating system
- Installing using the Dell Systems Management Tools and Documentation media
- Installing using the Red Hat Enterprise Linux 6 installation media
- Installing with Dell Unified Server Configurator
- Installing on systems with a Dell Utility Partition
- Installing in the Conventional (BIOS) mode
- Installing In The UEFI Mode
- Installing on devices that support multipathing
- Installing on iSCSI storage
- Installing using the Software iSCSI initiator
- Installing using the hardware iSCSI initiator
- Installing on FCoE-enabled storage
- Add-on device drivers
- Updating your system packages using the Red Hat Network
- Important information
- Known issues in Red Hat Enterprise Linux 6.6
- Resolved issues
in Red Hat Enterprise Linux 6.6
- Kernel panic occurs when OMSA services are started on Red Hat Enterprise Linux 6.5
- Unable to Install Red Hat Enterprise Linux 6.5 with an existing brtfs partition
- Underscore is missing for the interface name of Vindicator 2 Emulex card on network page
- Unable to boot Red Hat Enterprise Linux 6.5, after successful installation in UEFI mode
- DDR DMA testing fails in ethtool on Red Hat Enterprise Linux 6.5 Hypervisor
- Using IPv6 with Mozilla Firefox displays certification error
- Data unavailability occurs on Dell EqualLogic arrays due to Linux multipathing
- Red Hat Enterprise Linux 6.5 displays the ata1.01: failed to resume link (Scontrol 0) error message
- Red Hat Enterprise Linux 6.5 fails to boot from iSCSI LUNs
- Known issues
in Red Hat Enterprise Linux 6.5
- Booting with kernel parameters results in DMAR errors
- Xserver crashe, while booting Red Hat Enterprise Linux 6.5 after installation
- Invalid naming conventions for the ports of Vindicator 2 Emulex card when NPAR-EP is enabled
- NVMe Devices Are Not Identified During Operating System Installation
- Red Hat Enterprise Linux 6 fails when the DSDT in the BIOS has IPMI Opregion enabled
- Lifecycle Controller (USC based installation) deployment fails when installing Red Hat Enterprise Linux 6.x
- ethtool does not rReport 40 GB for Mellanox ConnectX-3 40 GB adapter
- Blurred display when changing resolution in Red Hat Enterprise Linux 6.5
- Resolved issues
in Red Hat Enterprise Linux 6.5
- Teamed NICs have no network connectivity
- Red Hat Enterprise Linux 6.4 installation on 10 GB iSCSI LUN from an EQL array hangs while creating a file system
- Ethtool reports 10GbE port speed instead of 40GbE when using Mellanox MLX4_EN driver
- Packet loss occurs when bonding device is configured in balanced-alb mode
- Known issues in Red Hat Enterprise Linux 6.4
- Resolved issues in Red Hat Enterprise Linux 6.4
- Known issues in Red Hat Enterprise Linux 6.3
- Resolved issues
in Red Hat Enterprise Linux 6.3
- Red Hat Enterprise Linux 6.2 kickstart installation may fail
- Network connections display the last used status as never in Red Hat Enterprise Linux 6
- Red Hat Enterprise Linux 6.2 displays a dbus netlink poll error after installation
- Network manager error in Red Hat Enterprise Linux 6.1 operating system log
- Red Hat Enterprise Linux 6.1 stops responding when iDRAC6 is reset
- Known issues in Red Hat Enterprise Linux 6.2
- Resolved issues in Red Hat Enterprise Linux 6.2
- Known issues
in Red Hat Enterprise Linux 6.1
- Red Hat Enterprise Linux 6.1 displays a bluez network manager error after installation
- Error message on starting IPMI drivers while installing OMSA
- Assigning iSCSI LUN target to Intel 10G network controller stops the operating system from booting
- Systems with Intel multiport i350 rNDC and PCI add-in adapters report incorrect/duplicate Mac address
- tg3 driver fails post Red Hat Network update
- Kernel panic occurs when GPGPU C2075 is installed on Red Hat Enterprise Linux 6.1
- Red Hat Enterprise Linux 6.1 installation fails
- Driver installation fails during Red Hat Enterprise Linux 6.1 installation
- dmesg error log displays a generic hardware error
- Resolved issues
in Red Hat Enterprise Linux 6.1
- Graphical boot splash screen in the UEFI mode is in low resolution
- PERC H700 DIMM failure messages with the debug kernel
- Network devices enumerated in an incorrect order
- OpenManage installation does not respond on Red Hat Enterprise Linux 6
- Red Hat Enterprise Linux 6 installation fails with virtual media
- Known issues in Red Hat Enterprise Linux 6
- Finding more information
- Getting help
Dell PowerEdge Systems Red Hat Enterprise Linux 6 (x86_64, x86) Installation Instructions and Important Information
Red Hat Enterprise Linux 6.5 displays the ata1.01: failed to resume link (Scontrol 0) error message
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\