Skip to main content
  • Розміщуйте замовлення швидко і легко
  • Переглядайте замовлення та відстежуйте свій статус доставки
  • Створення списку своїх продуктів і доступ до нього
  • Керуйте своїми сайтами, продуктами та контактами на рівні продуктів Dell EMC за допомогою адміністрації компанії.

First time setup of TeraDici 2400 PCoIP 4 port card

Summary: Steps for initial setup of your TeraDici 2400 PCoIP 4 port card.

This article may have been automatically translated. If you have any feedback regarding its quality, please let us know using the form at the bottom of this page.

Article Content


Symptoms

none

Cause

none

Resolution


This article provides information on how to setup the TeraDici 2400 PCoIP 4 port card for the first time.


Card installed but not configured.

First time setup of TeraDici 2400 PCoIP 4 port card.

If the card is functioning (but  not configured), you will see two additional "Standard" USB Controllers in Device Manager (Figure 1):

SLN297111_en_US__1Teradici1
Figure 1: Standard USB controllers in Device Manager


Configuration Process.

Configure the Teradici 2400 PCoIP 4 port card using the following steps:

  1. Open a browser of choice (Internet Explorer, Chrome, Firefox etc.) on the URL line Log in to the Teradici host card by typing the URL 192.168.1.100 (unless a DHCP server is present) the press the Enter Key.
SLN297111_en_US__2icon NOTE: If a DHCP server is present, Determine the IP address assigned to the Teradici card based on the MAC address of the card (The MAC address is on  a sticker on the card) then log in to the assigned MAC address. Once done, you can manually assign a IP address to the card outside the DHCP range.
  1. The PCoIP configuration page should appear. Click on Configuration, then click Initial Setup (Figure 2):

SLN297111_en_US__3Teradici2
Figure 2: Go to Initial Setup on PCoIP configuration page

  1. Check the box next to Enable HD Audio, Click Apply.
  2. Next, under the Network section, turn off Dynamic Host Configuration Protocol (DHCP)by un-checking the box next to Enable DHCP  and select a proper Static IP address for the network. (This information must be provided from the network in use.) Click Apply (Figure 3):

SLN297111_en_US__4Teradici3
Figure 3:Choose the Static IP address for the network

  1. In the Host Driver Function section, Check the check box to Enable the Host Driver Function, Click Apply (Figure 4):

SLN297111_en_US__5Teradici4
Figure 4:Enable the Host Driver Function

  1. In the Diagnostics menu, under PCoIP Processor, Schedule the PCoIP card to reset at the next system reboot. Restart the system (Figure 5):

SLN297111_en_US__6Teradici5
Figure 5: Schedule the PCoIP card to reset at next system boot

  1. After a reboot, two additional PCI Devices will appear in Device Manager (Figure 6):

SLN297111_en_US__7Teradici6
Figure 6: PCI Devices showing in Device Manager after reboot

  1. Install the latest PCoIP drivers (Figure 7):

SLN297111_en_US__8Teradici7
Figure 7: Install the latest drivers for the PCoIP

Optional: You may need to configure Monitor Emulation if you are not receiving an image on the remote device (Figure 8):

SLN297111_en_US__9Teradici8
Figure 8: Configure Monitor Emulation if no image appears on remote device


Article Properties


Last Published Date

20 Feb 2024

Version

4

Article Type

Solution