It's a good try This thread is about how to add seven new disks to a Data Domain system that has total five disks. So, the Data Domain system will have total 12 disks eventually.
Our conclusion was "use & follow Solve Desktop procedure". We can get the procedure from Solve Desktop's "Storage Expansion and Shelf Addition" section.
We also discussed briefly on an example of the procedure as follows, I have to emphasize this is just an example and hence cannot apply to all Data Domain system, though.
Check the current disk status [CLI: disk show state, GUI: Hardware > Storage > Status > Disk Status]
Physically add new disks to Data Domain
Wait till the Data Domain completely recognize the newly added disks. It would take around 10 minutes or so
JPCommunityMgr
Community Manager
Community Manager
•
3.1K メッセージ
0
2014年7月15日 17:00
username1さん
ディスカッションの投稿をありがとうございます。
しかしながら、ディスカッションがusername1さんのプライベートスペースに作成されてしまっているようですので、
お手数をおかけしてしまい申し訳ございませんが、本ディスカッションを日本語サポートフォーラムの「バックアップ/リカバリシステム」スペースへと移動して頂けないでしょうか。
※移動方法については、以下スレッドをご参照頂けますようお願い致します。
https://community.emc.com/docs/DOC-25114
プライベートスペースに投稿されたディスカッションは、EMC日本語サポートフォーラムサイトのコンテンツとして認識をされないために、日本語サポートフォーラムサイトへ訪れるユーザーから情報が見つかりにくくなってしまいます。
その結果、他のユーザーからの返信/回答を受け取る可能性が低くなってしまいますので、是非とも本ディスカッションを日本語サポートフォーラムの「バックアップ/リカバリシステム」スペースへ移動することについて、ご検討頂けますようお願い申し上げます。
参考情報:https://community.emc.com/docs/DOC-25221
Uehara Y.
Community Manager
Community Manager
•
4.9K メッセージ
1
2014年7月16日 01:00
username1さん
ご要望の内容について、まずはコマンドラインを利用した場合の例を簡単に箇条書きにし、その後でGUIの該当箇所を追記します。
ちなみにusename1さんはSolve Desktopをご利用可能でしょうか。ご利用できる場合には、「Storage Expansion and Shelf Addition」を選択することにより各モデル、DDOSごとに詳細な手順を作成することが出来るので、その出力結果を参照してディスクの追加からファイルシステムの拡張までの実施を行うようにしてください。
(EMCがオフィシャルで出している手順はSolve Desktopの手順です)
※上記は作業流れの一例です。この通りに実施することによりすべてのData Domainシステムのファイル拡張が出来るというわけではありません
そして、この手順をSystem Managerに当てはめると
1.、3.、5.についてはHardware > Storage > Status > Disk Statusで見れそうです
4.についてはSystem Settings > Licenses > [Add Licenses..]
6.については、実際にExpand出来るData Domainシステムをラボに見つけることが出来なかったので確実ではないのですが、恐らくData Management > File Systemの[More Tasks▼] > Expand Capacity... かと
7.はData Management > File System > Summaryで確認できると思います
ただし、可能であればやはりEMCオフィシャルな手順であるSolve Desktopの手順(コマンドラインを利用)をお勧めします。
user001a
1 Rookie
1 Rookie
•
340 メッセージ
0
2014年7月16日 02:00
Uehara Y. さん
詳細なご回答ありがとうございます。
コマンドでの実行が通例なのですね、GUIでの操作をお願いしてしまったために
回答を難しくしてしまってたいへん恐れ入ります。
Solve Desktopは使ったことがあります。
存在を忘れていて利用をまったく思いつきませんでしたが今後は
Solve Desktop も活用させて頂きます。
born_chen
1.8K メッセージ
0
2014年7月16日 07:00
以为可以照着部分中文看得懂,还是看不懂。
Uehara Y.
Community Manager
Community Manager
•
4.9K メッセージ
0
2014年7月17日 21:00
Hi Born_Chen-san,
It's a good try This thread is about how to add seven new disks to a Data Domain system that has total five disks. So, the Data Domain system will have total 12 disks eventually.
Our conclusion was "use & follow Solve Desktop procedure". We can get the procedure from Solve Desktop's "Storage Expansion and Shelf Addition" section.
We also discussed briefly on an example of the procedure as follows, I have to emphasize this is just an example and hence cannot apply to all Data Domain system, though.