未解決
この投稿は5年以上前のものです
43 メッセージ
0
3244
Unity コントローラ(Block)の冗長性について
以下のURLを参照すると、コントローラ(Block)の冗長性はActive / Activeだが、LUNはALUAの情報があります。
--------
http://lighthouse.emc.com/docs/DOC-54010
EMC Unity Q&A リスト
コントローラ(Block)の冗長性はActive / Active か、VNXと同様にActive / Passive (stanby)か?
→ Act / Act となります。(LUNはALUA)
--------
LUNがALUAということであれば、OptimalのSPのパスに偏ることとなり、実際にはActive / Passive (Stanby)
のように動作すると思うのですがUnityでのActive / Active とはどのように動作するのか、教えていただけ
ないでしょうか?
mihon
399 メッセージ
1
2016年8月25日 02:00
特定のLUNに着目するとVNXと同様にALUAです。
両コントローラがBlock/Fileの機能を分散して処理するため、コントローラとしてはAct/Actと表現しています。
nakamuu
43 メッセージ
0
2016年8月25日 19:00
Mihoさん、
早速のご回答ありがとうございます。
いただいたご回答の内容が記載されたドキュメントはございますでしょうか?
また、Blockでの運用する場合に、ゾーニング方法について、推奨されている
接続方法が記載されているドキュメントはございますでしょうか?
mihon
399 メッセージ
0
2016年8月25日 21:00
英語ですが、以下のホワイトペーパー P.14辺りから記載があります。
https://japan.emc.com/collateral/white-papers/h15162-emc-unity-high-availability.pdf
以下抜粋です。
Unity leverages Asymmetric Logic Unit Access (ALUA) for host access. This enables multiple paths to be active for I/O, but some paths are optimized while others are non-optimized.
Multi-pathing software, such as PowerPath, must be installed on the host in order to leverage ALUA. Multi-pathing software should be configured to use the optimized paths first and only use the non-optimized paths if there are no optimized paths available.
When using Fibre Channel, no configuration is required on the Unity system. However, when using a switched configuration, zoning may be needed on the switch to allow communication between the host and the Unity system. Create a zone for each one of the host’s HBA ports to each one of the SP’s FC ports.
The Fibre Channel World Wide Names (WWNs) for the Unity system’s FC ports are unique and can be found on the Settings page.
nakamuu
43 メッセージ
0
2016年8月28日 17:00
Mihoさん、
ご連絡ありがとうございます。
追加で確認させてください。
OS標準のパスソフトを使用した環境の場合、トレースパスで移動したLUNを、
オーナに戻す方法はございますか?
PowerPathをインストールしていれば、PawerPathコマンドで復旧できますが、
PowerPathをインストールしていない環境の場合、推奨方法を確認させていただき
たいです。
mihon
399 メッセージ
1
2016年8月31日 03:00
Unityでは機能がシンプルになっており、trespassは"SPオーナー変更"に集約されています。
GUIまたはCLIで、LUNのSPオーナー変更を行ってください。
主にSP-A,SP-Bの負荷に不均衡が起きた場合に有効です。
nakamuu
43 メッセージ
0
2016年9月1日 17:00
Mihoさん、
ご教授ありがとうございます。
またお礼が遅くなり申し訳ございません。
SPオーナー変更に集約されていること、承知いたしました。
CLI(UEMCLI)での具体的なコマンドとしては、以下の認識です。
もし認識が異なれば、ご指摘いただければ幸いです。
◆https://www.emc.com/collateral/TechnicalDocument/docu69330.pdf
- Change LUNs (p.323)
/stor/prov/luns/lun -id set -spOwner {spa | spb}
mihon
399 メッセージ
0
2016年9月6日 01:00
CLIはご認識の通りです。
nakamuu
43 メッセージ
0
2016年9月6日 03:00
お忙しいところ、ご教授ありがとうございました。