2 Intern
•
858 メッセージ
0
365
[powerstore]Base Port0,1ポートからのIPのマップ解除について
PowerStoreにて、ボンディングされているBasePort0,1に対して、ストレージネットワークを一度でも割り当てた場合、解除することは不可能となるでしょうか。
実機にて、
BaseEnclosure-NodeA-4PortCard-FEPort0
BaseEnclosure-NodeA-4PortCard-FEPort1
BaseEnclosure-NodeB-4PortCard-FEPort0
BaseEnclosure-NodeB-4PortCard-FEPort1
のポート(実際にはBondポート)にストレージネットワークを割り当てたところ、
[Hardware] > [Ports] > Ethernet の該当ポートには
"Mapped For Storage"と"Tagged For Replication"
に該当ストレージネットワーク名が割り当てられました。
しかし、その後それらのポートを選択しても[More Actions] > [Remove Mapping]などが選択できない状態になってしまいます。
ayas
Moderator
Moderator
•
6.5K メッセージ
1
2022年6月15日 17:00
keis3456さん
Bondポートであっても(System Bond )ストレージネットワークのRemove は可能です。
ただそのポートが"Mapped For Storage"と"Tagged For Replication"になっている場合
それができません。そのため"Mapped For Storage"=該当ポートで動作しているストレージネットワークがあるので他のポートへの移動をする、又"Tagged For Replication"=このポートでReplicationタグがあるのでそのタグを外す、必要があります。
参考KB:Dell EMC Knowledge Article 000191976 : PowerStore : A secondary [Replication] Storage Network is also available as iSCSI network and cannot be deleted.
(Replication用にポートが使われているとRemoving / Deleting that network ができないという話)
keis3456
2 Intern
2 Intern
•
858 メッセージ
0
2022年6月15日 18:00
ayasさん
ご回答ありがとうございます。
確かに実機にてPort2のほうにマップ(Mapped For Storage , Tagges For Replication)を追加で設定し、その後Bondポートを選択したところ、Remove Mapを選択することができました
そこで疑問点としてPowerStoreの仕様上、レプリケーションなどは
Bondポート部分のTORスイッチへの接続が必須で、Bondポートから
PowerStore間で通信がやりとりされると認識しておりましたが
この部分は認識間違いでしょうか。
ayas
Moderator
Moderator
•
6.5K メッセージ
1
2022年6月16日 00:00
keis3456さん
ご返信をありがとうございます。
先述のKBに以下のコメントを見るとReplicationのやり取りについてはほかのポートでも大丈夫そうです。
When planning for replication using the default configuration, consider that the ports are also used for other traffic like I/O for iSCSI host access, migration, and file (PowerStore T models only). If these features are used, it is recommended to plan replication using dedicated interfaces.
Extra ports use dynamic storage IP configuration from the range which was given in ICW or added in the networking section of PowerStore Manager.
keis3456
2 Intern
2 Intern
•
858 メッセージ
0
2022年6月16日 01:00
ご連絡ありがとうございます。
KBコメントにて、デフォルト構成の場合はiSCSIやレプリケーションなども該当ポート(Port0,Port1)に流れるため、レプリケーションなどは他のポートに分けて専用ポートにしたほうがよいとの記載があること確認いたしました。
ありがとうございます。