Powering a Data Domain System On or Off This topic describes how to power on or power off a Data Domain system.
Procedure
1.Power on any expansion shelves before powering on the Data Domain controller. The ES30 powers on when plugged in. Wait approximately three minutes after all expansion shelves are turned on.
Note
The controller is the chassis and any internal storage. A Data Domain system refers to the controller and any optional external storage.
2.Plug in the power cord for your controller, and if the controller has a power button, press the controller’s power button (as shown in the Installation and Setup Guide for your Data Domain system).
3.To shut down power to a Data Domain system, use the system poweroff CLI command.
This command automatically performs an orderly shut down of DD OS processes and is available to administrative users only.
Results
CAUTION
Do not use the chassis power switch to power off the system. Doing so prevents remote power control using IPMI. Use the system poweroff command instead. The system poweroff command shuts down the system and turns off the power.
1. Power on any expansion shelves before the controller. ES20 enclosures power on using switches, ES30 enclosures power on when plugged in to AC power. Wait approximately three minutes after all expansion shelves are turned on.
2. Push the controller’s power button (as shown in the Installation and Setup Guide for your Data Domain system). The system can be powered down only from the CLI.
3. Verify the system has come up. This can be done with the system console or from a SSH session to the Data Domain system. The system is up when you can log into the system.
To shut down power to the Data Domain system:
Use the system poweroff command. The command automatically performs an orderly shut down of DD OS processes. The command is available to administrative users only.
Caution: Do not use the chassis power switch to power off the system. Doing so will prevent the ability of the system to be remotely powered up using IPMI. Use the following command instead.
The ‘system poweroff’ command shuts down the system and turns off the power.
born_chen
1.8K 消息
0
2014年8月25日 00:00
开机就不用多说啦。接通电源开机即可。
参考关机。
Powering a Data Domain System On or Off This topic describes how to power on or power off a Data Domain system.
Procedure
1.Power on any expansion shelves before powering on the Data Domain controller. The ES30 powers on when plugged in. Wait approximately three minutes after all expansion shelves are turned on.
Note
The controller is the chassis and any internal storage. A Data Domain system refers to the controller and any optional external storage.
2.Plug in the power cord for your controller, and if the controller has a power button, press the controller’s power button (as shown in the Installation and Setup Guide for your Data Domain system).
3.To shut down power to a Data Domain system, use the system poweroff CLI command.
This command automatically performs an orderly shut down of DD OS processes and is available to administrative users only.
Results
CAUTION
Do not use the chassis power switch to power off the system. Doing so prevents remote power control using IPMI. Use the system poweroff command instead. The system poweroff command shuts down the system and turns off the power.
管理手册上P32。
born_chen
1.8K 消息
0
2014年8月25日 00:00
不用,OS内置会启动这些服务的。那要是都要开机之后去操作,那不很麻烦了。
mobe_chang
221 消息
0
2014年8月25日 00:00
請教開機不需要像avamar一般,需要一些啟動服務的指令嗎?
mobe_chang
221 消息
0
2014年8月25日 00:00
感謝您的說明~
DELL-Leo
Community Manager
Community Manager
•
7.1K 消息
2
2014年8月25日 01:00
Hey Mobe,
这边有一个专门讲解DD开机和关机的KB,你可以参考。
Power On and Power Off a Data Domain System
To turn on a Data Domain system:
1. Power on any expansion shelves before the controller. ES20 enclosures power on using switches, ES30 enclosures power on when plugged in to AC power. Wait approximately three minutes after all expansion shelves are turned on.
2. Push the controller’s power button (as shown in the Installation and Setup Guide for your Data Domain system). The system can be powered down only from the CLI.
3. Verify the system has come up. This can be done with the system console or from a SSH session to the Data Domain system. The system is up when you can log into the system.
To shut down power to the Data Domain system:
Use the system poweroff command. The command automatically performs an orderly shut down of DD OS processes. The command is available to administrative users only.
Caution: Do not use the chassis power switch to power off the system. Doing so will prevent the ability of the system to be remotely powered up using IPMI. Use the following command instead.
The ‘system poweroff’ command shuts down the system and turns off the power.
# system poweroff
Continue? (yes|no|?) [no]: yes
mobe_chang
221 消息
0
2014年8月25日 01:00
Hi Leo:
非常謝謝,我把他藏起來,
DELL-Leo
Community Manager
Community Manager
•
7.1K 消息
0
2014年8月25日 02:00
不客气~
DELL-Leo
Community Manager
Community Manager
•
7.1K 消息
0
2014年9月1日 20:00
Hey Mobe,
我把上面的KB翻译了一下,你可以查看此中文文档。
如何对 Data Domain 系统进行正确的开机和关机操作
mobe_chang
221 消息
0
2014年9月1日 21:00
Hi Leo:
對我這種英文程度不好的人,真是一大福音啊!
您真是太專業了啦~
DELL-Leo
Community Manager
Community Manager
•
7.1K 消息
0
2014年9月1日 21:00
客气~ 尽量做到有求必应!