Highlighted
cncommunitymgr
3 Silver

【微信群提问分享】VNX的SPS B换了GUI里还是报错

转到解答

微信群用户“B”提问:


SPS B换了还是报错,VNX5100要怎么操作?


mmexport1485143218216.jpg

标签 (1)
标记 (4)
0 项奖励
1 个已接受解答

已接受的解答
cncommunitymgr
3 Silver

Re: 【微信群提问分享】VNX的SPS B换了GUI里还是报错

转到解答

微信群用户”T“ 回复:


要么监控线没连好,要么是电池不兼容。


微信群用户”TM“ 补充:


VNX换电池那个F不是马上就消失,等充满电再看吧,先可以确定的是看看该SPS的状态是不是not ready。


微信群用户”M“ 补充:


没业务的话断电再加电,从界面重启没用。


微信群用户”R“ 回复:


@M,是的,安装KB做法,需要cold power cycle冷启动:


Use the following workaround in order of increasing impact for immediate mitigation to the problem: 

  1. Pull sense cable inspect for pushed pins, replace if necessary. If not, hold out for at least three seconds then re-insert. Perform the action on the peer SP only if necessary.
  2. Reboot the SP on the side that is reporting the error.
  3. Reboot the other SP.
  4. Cold power cycle the xPE enclosure.

After performing above workaround, verify from the GUI that the SPS is no longer reported as faulted.

Warning! Under NO circumstances should the SPS cables be swapped around if one of the SPS is working correctly. This could lead to write cache being DISABLED.



0 项奖励
2 条回复2
cncommunitymgr
3 Silver

Re: 【微信群提问分享】VNX的SPS B换了GUI里还是报错

转到解答

微信群用户”T“ 回复:


重启SP A试一下。


用户"S"补充:


A和B都重启。另外VNX可以尝试调节test时间来带动电池检测,这样也有可能不需要重启SP。



微信群用户“B”回复:


SP A、B重启了还是一样。日志:


mmexport1485143221163.jpg


mmexport1485143226949.jpg


mmexport1485143223964.jpg


cncommunitymgr
3 Silver

Re: 【微信群提问分享】VNX的SPS B换了GUI里还是报错

转到解答

微信群用户”T“ 回复:


要么监控线没连好,要么是电池不兼容。


微信群用户”TM“ 补充:


VNX换电池那个F不是马上就消失,等充满电再看吧,先可以确定的是看看该SPS的状态是不是not ready。


微信群用户”M“ 补充:


没业务的话断电再加电,从界面重启没用。


微信群用户”R“ 回复:


@M,是的,安装KB做法,需要cold power cycle冷启动:


Use the following workaround in order of increasing impact for immediate mitigation to the problem: 

  1. Pull sense cable inspect for pushed pins, replace if necessary. If not, hold out for at least three seconds then re-insert. Perform the action on the peer SP only if necessary.
  2. Reboot the SP on the side that is reporting the error.
  3. Reboot the other SP.
  4. Cold power cycle the xPE enclosure.

After performing above workaround, verify from the GUI that the SPS is no longer reported as faulted.

Warning! Under NO circumstances should the SPS cables be swapped around if one of the SPS is working correctly. This could lead to write cache being DISABLED.



0 项奖励