Highlighted
SteeleGTX
Bronze

Dimension 2400 blinking yellow/amber light

Jump to solution

I cold boot my tower but when I powered it back up I get a black screen on my monitor and I check the tower to see a yellow/amber colored light instead of the usual green power indicator.  Held down the power button till the pc shutdown.  Unplugged all wires from the back except for power supply, keyboard, mouse and monitor.  Powered up the tower again and still getting the same issue.  Any help would be greatly appreciated.

0 Kudos
9 Replies
shesagordie
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

SteeleGTX

Does the power supply fan run?

Are there any disgnostic lights lite on the back panel?

See HERE

<ADMIN NOTE: Broken link has been removed from this post by Dell>

A blinking amber power button LED, usually indicates a power failure, first open the case and check that all the power cables are properly connected, if this fails to correct the problem, then replace the power supply.

Because the 2400 has a open back, you can use most generic standard ATX PSU, with or without, the on/off switch and either a 20-pin or 20+4-pin main motherboard power connector, you should be able to buy a compatible power supply from a local, or online computer store.

Bev.

 

If my answer was helpful, please use the 'Did this answer the question' and click: Yes
Forum Member since 2001
I am not employed by Dell

0 Kudos
SteeleGTX
Bronze

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

The power supply fan initially starts for a second then off.

This 2400 doesn't have the diagnostic lights in the back panel.

Going to get a new power supply but not quite sure how to install it.  Do you have a link or instructions 'how to' remove and install the power supply 'properly'.

Checked the manual on the site but the table of contents don't specify how to replace/install power supply.

Thanks again for the speedy feedback.

jackshack
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

Of course it does.  See here:  Dimension 2400 Power Supply. <ADMIN NOTE: Broken link has been removed from this post by Dell>

Dell Forum member since 2005

0 Kudos
shesagordie
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

SteeleGTX

The Dimension 2400 does have four diagnostic lights, they are located between the PS2 Mouse/keyboard connectors and the Serial port on the back panel.

The Dimension Model 2300 does not have any diagnostic lights.

Bev.

 

If my answer was helpful, please use the 'Did this answer the question' and click: Yes
Forum Member since 2001
I am not employed by Dell

SteeleGTX
Bronze

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

My computer is working fine now.  Thank you for all your help.

0 Kudos
shesagordie
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

SteeleGTX

Happy to hear that the problem is resolved.

Bev.

 

If my answer was helpful, please use the 'Did this answer the question' and click: Yes
Forum Member since 2001
I am not employed by Dell

0 Kudos
mdgettm
Copper

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

thx for power supply link - already saw that online - problem I have is reconnecting cables from power supply -cables labelled p3, p8 p9 etc goes to disc drive, vs power switch, vs 3.5" drive etc...- which cable to which item?

0 Kudos
shesagordie
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

thx for power supply link - already saw that online - problem I have is reconnecting cables from power supply -cables labelled p3, p8 p9 etc goes to disc drive, vs power switch, vs 3.5" drive etc...- which cable to which item?

 
mdgettm 
 
You basically cannot make a mistake connecting the cables to the different drives and motherboard, all the connectors are 'keyed' [different shape and size] to fit into the appropiate sockets.
 
P1 [20-pin] connects to the motherboard
 
P2  [4-pin] connects to the motherboard
 
P3,P5,P6,P8,P9 [4-pin] connect to the IDE/EIDE Drives
 
P7 connects to the floppy drive.
 
For more information, go here:-
 

<ADMIN NOTE: Broken link has been removed / replaced from this post by Dell>

 
Bev.
 
 

 

 

If my answer was helpful, please use the 'Did this answer the question' and click: Yes
Forum Member since 2001
I am not employed by Dell

0 Kudos
shesagordie
Diamond

Re: Dimension 2400 blinking yellow/amber light

Jump to solution

thx for power supply link - already saw that online - problem I have is reconnecting cables from power supply -cables labelled p3, p8 p9 etc goes to disc drive, vs power switch, vs 3.5" drive etc...- which cable to which item?

 
mdgettm 
 
You basically cannot make a mistake connecting the cables to the different drives and motherboard, all the connectors are 'keyed' [different shape and size] to fit into the appropiate sockets.
 
P1 [20-pin] connects to the motherboard
 
P2  [4-pin] connects to the motherboard
 
P3,P5,P6,P8,P9 [4-pin] connect to the IDE/EIDE Drives
 
P7 connects to the floppy drive.
 
For more information, go here:-
 

<ADMIN NOTE: Broken link has been removed / replaced from this post by Dell>

 
Bev.
 
 

 

 

If my answer was helpful, please use the 'Did this answer the question' and click: Yes
Forum Member since 2001
I am not employed by Dell

0 Kudos