Unsolved
This post is more than 5 years old
3 Posts
0
334863
MIBs for Dell Powerconnect 34xx and 54xx
hi,
i'm trying to find mibs for my network switches to monitor it with nagios (snmp).
someone has a link or others where i can get the oids?
Need:
- CPU
- Powersupply
- FAN
- etc...
thx
nrls24
10 Posts
0
December 29th, 2008 10:00
hi,
you can download the mibs from the dell ftp-server:
ftp://ftp.dell.com/network/PowerConnect54xx_MIBs_A00.zip
ftp://ftp.dell.com/network/PowerConnect34xx_MIBs_A01.zip
I monitor the following oids from my 3400 with nagios:
If you have a 34XXP, then you can also monitor fan3-fan5 (67109251-67109253). Also interesting might be the power comsumption of your devices:
Perhaps someone else knows the oids for memory usage?
Hope that helps. I don't have 54XX in my network, just 53XX and 62XX.
best regards...
Nils
RedRussell1980
3 Posts
0
May 21st, 2009 05:00
Hi Nils,
I require the OID's for Temperature and CPU for the PowerConnect 62XX. If there is any chance you could pass these on you'd be doing me a huge favour.
Regards
Russell
DELL-Victor
98 Posts
0
May 21st, 2009 12:00
Hello!
The Temperature OID's are not present for the current 62xx firmware (2.2.0.3), but will be included in the next set of firmware and MIB revisions, dubbed 3.0 due to come out by the end of June. Included is a new MIB called FASTPATH-BOXSERVICES-PRIVATE-MIB which will contain the OID .1.3.6.1.4.1.674.10895.5000.2..6132.1.1.43.1.8.1.4 for the temperature sensor reading.
I'm not able to locate CPU utilization and am looking further into the issue. If not present, I'll request the addition for the next MIB release.
Victor
trentg
11 Posts
0
October 27th, 2009 14:00
Here we are near November and I see no newer firmware for the 6248. I'd like to be able to pull temps since ours are burning up in the top of full racks. Any ideas? Thanks.
Edit: I've looked at the drivers and downloads page for my 6248 svc tags and without them just choosing the product and I see no 3.x firmware available.
Trent
DELL-Victor
98 Posts
0
October 27th, 2009 15:00
The 3.x firmware is still in the works and due to be out very soon. Until available you do still have the options of pulling the temps through the cli or web ui. The cli command is "show system" and will provide you the temperature, temperature status, fan and power supply status. The web ui under the General-Health page shows the same information. I hope this is some help for now until the fw becomes available.
-Victor
rodrigopalmito
4 Posts
1
June 17th, 2010 07:00
How can i monitor CPU utilization of PC6248???
In Dell FTP, have only MIBs to old firmware. What MIB have this monitor of CPU?
vt1012
212 Posts
0
June 17th, 2010 09:00
Using 6248 3.2.x.x firmware the CPU util oids are
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 and
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.3
The updated MIB is included in the firmware zip file PC6200v3.2.0.7.zip.
hope this helps.