Unsolved
This post is more than 5 years old
5 Posts
0
53869
PowerConnect 3424P firmware upgrade problem
I bought a 3424P recently and tried to upgrade the firmware. I dont remember the version of the old firmware, but it was pretty old. I read about how I was supposed to upgrade both the firmware and the program version at the same time or Id end up in an endless reboot loop, and I thought I had done it correctly using tftp, but apparently not. Now I am stuck in the endless loop. When I start the switch I have the software version 2.0.0.31 running with boot version 1.0.1.01 Built 15-Jun-2006 and hardware version 00.00.02 .
So I tried to follow the instructions on how to recover from this, andI have tried using XMODEM to send the older software version to get out of this loop, but it wont work. The download proceeds as planned, but I get an error about decompressing the file. Ive tried several different software versions without any success. I need some help on what to do next.
These filese are big and it takes a long time to send them over. I increased the baud rate to 115200 to make it go faster...does this have anything to do wih my failure?
Here is the whole hyperterminal transcript:
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
:emotion-14: Stack menu
[7] Back
Enter your choice or press 'ESC' to exit:
Set new device baud-rate: 115200g/N
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
:emotion-14: Stack menu
[7] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x40e700 records...
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.1.01 Built 15-Jun-2006 11:42:56
Carrier board, based on PPC8247
128 MByte SDRAM. I-Cache 16 KB. D-Cache 16 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
LZMA: Compressed File Version not supported!
Switching to the second image ...
Perform WARM BOOT ...
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.1.01 Built 15-Jun-2006 11:42:56
Carrier board, based on PPC8247
128 MByte SDRAM. I-Cache 16 KB. D-Cache 16 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-2
100%
OK
Running from RAM...
*********************************************************************
*** Running SW Ver. 2.0.0.31 Date 30-Sep-2009 Time 15:55:36 ***
*********************************************************************
HW version is 00.00.02
Base Mac address is: 00:11:43:f7:94:12
Dram size is : 128M bytes
Dram first block size is : 106496K bytes
Dram first PTR is : 0x1800000
Flash size is: 16M
01-Jan-2000 01:01:04 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
01-Jan-2000 01:01:07 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
alid device type is found: 268374443 on device 0
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 2.0.0.31 (date 30-Sep-2009 time 15:55:36)
0xb5128
0x3dced0
0x291710
0x291bcc
0x295ab0
0x2b1ec4
0x2b2194
0x4d0574
0x4d0b34
0x4d11b0
0x4e52e4
0x4f0c80
0x4813b4
0x484e38
0x3e1e50
0xd3dc4
0xa9ca0
**************************************************
***************** SYSTEM RESET *****************
**************************************************
prsmith777
5 Posts
0
January 2nd, 2010 21:00
I also did try erasing the flash file config as well without success.
prsmith777
5 Posts
0
January 3rd, 2010 15:00
I tried today to send the .ros file at 9600 baud with similar errors.
I guess the baud rate didnt have much to do with it.
prsmith777
5 Posts
0
January 14th, 2010 07:00
Anyone have any thoughts?
hans555
18 Posts
0
January 14th, 2010 14:00
The only chance to recover is to do Erase Flash Sector inside the Advance Menu
In the boot menu press simultaneus CTRL-Shift-6 then press Enter
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
:emotion-14: Stack menu
[7] Advanced menu
:emotion-29: Back
Select option# 7 for advance menu to get the advance options.
Advanced menu
[1] Stacking port menu
[2] Erase Flash Sectors
[3] Image menu
[4] MAC and Board Info menu
[5] MFG mode menu
:emotion-14: Debug mode menu
[7] Back
Select option# 2 to erase flash sectors
This what you will see
Warning! About to erase flash!
FLASH size = 0xfe0000. Sectors = 119
Are you sure (Y/N) ? y
Enter First flash sector (1 - 119): 1
Enter Last flash sector (1 - 119): 119
After it erase the sector go ahead and upload the firmware or ROS file using XModem from the startup menu.
use baud rate of 38400. Use firmware version 2.0.0.31 (PowerConnect_34xx-20031.ros) to match boot-code version 1.0.1.01.
prsmith778
1 Message
0
January 14th, 2010 21:00
Hans,
This is actually prsmith777...Dell locked me out of my account for 24 hours for too many bad sign on attempts...so I created this account
I thank you for your instructions, and I followed them exactly...but the results are the same. I tried various baud rates and tried reloading the .ros file thinking maybe it was corrupted, but no luck.
This is an out of warranty switch purchased from a reseller and Id really like to try my hardest to correct the issue before paying for repair/tech support..
Are there any other ideas to try? Is it possible the boot version is not correct and thus the .ros file is not compatible? I didnt really want to try that unless it is a viable solution given the long time to xmodem the file to the switch.
I did find this link at the cisco forum which has me a bit worried: http://forums.linksysbycisco.com/linksys/board/message?board.id=Switches&message.id=227
Here is what the log reads:
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
:emotion-14: Stack menu
[7] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x32d380 records...
Setting checksum: 0x1910f922 , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.1.01 Built 15-Jun-2006 11:42:56
Carrier board, based on PPC8247
128 MByte SDRAM. I-Cache 16 KB. D-Cache 16 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%
OK
Running from RAM...
*********************************************************************
*** Running SW Ver. 2.0.0.31 Date 30-Sep-2009 Time 15:55:36 ***
*********************************************************************
HW version is 00.00.02
Base Mac address is: 00:11:43:f7:94:12
Dram size is : 128M bytes
Dram first block size is : 106496K bytes
Dram first PTR is : 0x1800000
Flash size is: 16M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
01-Jan-2000 01:01:07 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
alid device type is found: 268374443 on device 0
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 2.0.0.31 (date 30-Sep-2009 time 15:55:36)
0xb5128
0x3dced0
0x291710
0x291bcc
0x295ab0
0x2b1ec4
0x2b2194
0x4d0574
0x4d0b34
0x4d11b0
0x4e52e4
0x4f0c80
0x4813b4
0x484e38
0x3e1e50
0xd3dc4
0xa9ca0
**************************************************
***************** SYSTEM RESET *****************
**************************************************
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
01-Jan-2000 01:01:07 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
alid device type is found: 268374443 on device 0
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 2.0.0.31 (date 30-Sep-2009 time 15:55:36)
0xb5128
0x3dced0
0x291710
0x291bcc
0x295ab0
0x2b1ec4
0x2b2194
0x4d0574
0x4d0b34
0x4d11b0
0x4e52e4
0x4f0c80
0x4813b4
0x484e38
0x3e1e50
0xd3dc4
0xa9ca0
**************************************************
***************** SYSTEM RESET *****************
**************************************************
hans555
18 Posts
0
January 15th, 2010 07:00
PRSMITH,
I do not belive the boot-code 1.0.1.01 is a problem because we are still able to get to the boot menu.
All firmware 2.0.x.x.ROS will be compatible to boot-code 1.0.1.01.
If you had done "Erase Flash Sectors" not "Erase Flash File" and did XModem the ROS file correctly then maybe this switch is host.
Maybe give it one last shot and download the file from the ftp sites:
ftp://ftp.us.dell.com/network/PowerConnect_34xx-20031.zip
prsmith777
5 Posts
0
January 15th, 2010 18:00
I tried it and the same problem.
I am going to try the other firmware versions and see what happens
there are:
2.0.0.20
2.0.0.21
2.0.0.29
2.0.0.30
which are supposed to work with boot 1.0.1.01
Wish me luck
alterpeople
2 Posts
0
March 26th, 2010 15:00
same problem , i've uploaded 2.0.0.20 by xmodem and just played on "set data breakpoint" and disable watchdog in the secret menu .
I can post the error , end in the diagnostic mode too.
Can be nice to get the password to play mooore ... :D
Someone have the same problem on a linksys stuff , developed like this equipment on cisco engineering ( I think :-/ )
I'd like someone in dell engineering can answear us for this SOFTWARE issue.
All other test in the diag mode are ok.
AltErPeopLe
.......
BOXP_get_pp_list - return pp_PTR - for dev_num= 6
BOXG_get_pp_info - ENTRY : dev_num= 7, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 8, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 9, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 10, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 11, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 12, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 13, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 14, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 15, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 16, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 17, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 18, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 19, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 20, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 21, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 22, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 23, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 24, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 25, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 26, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 27, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 28, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 29, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 30, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 31, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 32, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 33, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 34, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 35, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 36, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 37, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 38, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 39, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 40, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 41, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 0, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 0
BOXG_get_pp_info - ENTRY : dev_num= 1, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 1
BOXG_get_pp_info - ENTRY : dev_num= 2, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 2
BOXG_get_pp_info - ENTRY : dev_num= 3, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 3
BOXG_get_pp_info - ENTRY : dev_num= 4, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 4
BOXG_get_pp_info - ENTRY : dev_num= 5, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 5
BOXG_get_pp_info - ENTRY : dev_num= 6, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 6
BOXG_get_pp_info - ENTRY : dev_num= 7, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 8, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 9, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 10, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 11, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 12, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 13, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 14, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 15, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 16, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 17, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 18, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 19, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 20, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 21, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 22, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 23, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 24, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 25, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 26, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 27, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 28, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 29, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 30, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 31, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 32, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 33, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 34, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 35, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 36, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 37, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 38, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 39, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 40, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 41, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 0, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 0
BOXG_get_pp_info - ENTRY : dev_num= 1, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_gt - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 1
BOXG_get_pp_info - ENTRY : dev_num= 2, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 2
BOXG_get_pp_info - ENTRY : dev_num= 3, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 3
BOXG_get_pp_info - ENTRY : dev_num= 4, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 4
BOXG_get_pp_info - ENTRY : dev_num= 5, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 5
BOXG_get_pp_info - ENTRY : dev_num= 6, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 6
BOXG_get_pp_info - ENTRY : dev_num= 0, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 0
BOXG_get_pp_info - ENTRY : dev_num= 1, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 1
BOXG_get_pp_info - ENTRY : dev_num= 2, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 2
BOXG_get_pp_info - ENTRY : dev_num= 3, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 3
BOXG_get_pp_info - ENTRY : dev_num= 4, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 4
BOXG_get_pp_info - ENTRY : dev_num= 5, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 5
BOXG_get_pp_info - ENTRY : dev_num= 6, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 6
BOXG_get_pp_info - ENTRY : dev_num= 0, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 0
BOXG_get_pp_info - ENTRY : dev_num= 1, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 1
BOXG_get_pp_info - ENTRY : dev_num= 2, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 2
BOXG_get_pp_info - ENTRY : dev_num= 3, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 3
BOXG_get_pp_info - ENTRY : dev_num= 4, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 4
BOXG_get_pp_info - ENTRY : dev_num= 5, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 5
BOXG_get_pp_info - ENTRY : dev_num= 6, unit_idx=0, slot_idx= 0
BOXP_get_pp_list - BOXP_get_slot_info: NOT NULL slot_PTR
BOXP_get_pp_list - num_of_PP_obj > 0 = OK
BOXP_get_pp_list - return pp_PTR - for dev_num= 6
BOXG_get_pp_info - ENTRY : dev_num= 7, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 8, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 9, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 10, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 11, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 12, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 13, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 14, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 15, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 16, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 17, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 18, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 19, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 20, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 21, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 22, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 23, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 24, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 25, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 26, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 27, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 28, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 29, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 30, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 31, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 32, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 33, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 34, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 35, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 36, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 37, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 38, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 39, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 40, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULL
BOXG_get_pp_info - ENTRY : dev_num= 41, unit_idx=255, slot_idx= 255
BOXG_get_pp_info - check : unit_idx=ILLEGAL 255 or slot_idx= ILLEGAL 255
BOXG_get_pp_info - return NULLTapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 01:01:20 %INIT-I-InitCompleted: Initialization task is completed
Start diagnostics please wait.
>01-Jan-2000 01:01:20 %Box-I-FAN-STAT-CHNG: FAN# 1 status is - operational.
01-Jan-2000 01:01:20 %Entity-I-SEND-ENT-CONF-CHANGE-TRAP: entity configuration c
hange trap.
01-Jan-2000 01:01:20 %Box-I-FAN-STAT-CHNG: FAN# 2 status is - operational.
01-Jan-2000 01:01:20 %Box-I-PS-STAT-CHNG: PS# 1 status is - operational.
HOST Tests
[1 ] DRAM
[2 ] Flash
[3 ] UART
[4 ] Timers
[5 ] I2C
[6 ] Hardware Reset
[7 ] Test All
[8 ] Esc
Enter your choice: 5
I2C Test
--------
Notice: This test may take several minutes!
Searching for I2C known devices:
----------------
Address: 0xa0 Index: 0x01 Device not found.
Address: 0xa0 Index: 0x02 Device not found.
Address: 0x98 Index: 0x00 Device Type: Unknown module.
I2C devices test......................................FAIL
Diagnostic MENU
[1 ] HOST Tests
[2 ] Board Info
[3 ] Environmental tests
[4 ] Show configuration
[5 ] PP Tests
[6 ] PHY Tests
[7 ] Logfile
[8 ] Esc
Enter your choice:
<ADMIN NOTE:Email Id removed per privacy policy>
rogerc100
1 Message
0
April 8th, 2010 12:00
hello, i have the same problem but with the dell 3448p switch...........
did you get any answers to this, i can't seem to read any replies to your post on the forum....\
thanks
email:
<ADMIN NOTE:Email Id removed per privacy policy>
alterpeople
2 Posts
0
April 8th, 2010 19:00
no , i haven't got any answear.
There are more hardware , and not only manufactured by dell ( ... ) affected .
I read somewhere that solving this issue was beginning to cost more than platform development but this is a rumour.
smeek
4 Posts
1
March 12th, 2012 11:00
I am having a similar issue. I was able to pull back older image by choosing option 11 on boot menu, but I still can't get newer firmware to load after downloading and trying several different versions.
11 - Activate Backup Image