Highlighted
SHAFA4
Bronze

7048 Routing/DHCP relay with 5548

Jump to solution

Hi, 

I am having issue with the 5548 not relaying the DHCP request for PXE (SCCM), 5548 is connected to 7048 (Trunk). We are Cisco shop, this is the first time I am using DELL. Any help is appreciated.

--------
7048
--------

!Current Configuration:
!System Description "PowerConnect 7048, 4.2.2.3, VxWorks 6.6"
!System Software Version 4.2.2.3
!System Operational Mode "Normal"
!
configure
gvrp enable
vlan database
vlan 2,10-11,21,50-52,156
vlan routing 1 1
vlan routing 10 2
vlan routing 21 3
vlan routing 50 4
vlan routing 51 5
vlan routing 52 6
vlan routing 156 7
vlan routing 2 8
vlan routing 11 9
vlan association subnet 10.112.0.0 255.255.252.0 10
vlan association subnet 10.112.4.0 255.255.255.0 11
vlan association subnet 10.116.4.0 255.255.252.0 21
slot 1/0 5 ! PowerConnect 7048
slot 1/1 11 ! SFP+ Card
slot 1/2 9 ! CX4 Card
slot 2/0 6 ! PowerConnect 7048P
slot 2/1 11 ! SFP+ Card
slot 2/2 9 ! CX4 Card
stack
member 1 5 ! PCT7048
member 2 6 ! PCT7048P
ip routing
ip route 0.0.0.0 0.0.0.0 192.168.1.58
ip route 10.0.0.0 255.0.0.0 192.168.1.58
interface vlan 1
exit
interface vlan 2
ip address 192.168.1.57 255.255.255.252
ip local-proxy-arp
no ip redirects
exit
interface vlan 10
ip address 10.112.0.1 255.255.252.0
no ip redirects
exit
interface vlan 11
ip address 10.112.4.1 255.255.255.0
ip helper-address 10.112.1.50
ip local-proxy-arp
no ip redirects
exit
interface vlan 21
ip address 10.116.4.1 255.255.252.0
ip helper-address 10.112.1.50
ip helper-address 10.112.1.51
exit
interface Te1/1/2
description 'F2_NTR_4'
gvrp enable
spanning-tree portfast
switchport mode trunk
dot1x port-control force-authorized
exit



------
5548
------

vlan database
vlan 10-11,21
exit

gvrp enable

ip dhcp relay enable

stack master unit 1
!
interface vlan 1
ip address dhcp
!
interface vlan 10
ip address 10.112.0.4 255.255.252.0
ip dhcp relay enable
ip proxy-arp

interface gigabitethernet1/0/18
spanning-tree portfast
switchport access vlan 21

ip route 0.0.0.0 0.0.0.0 10.112.0.1

interface tengigabitethernet1/0/1
description F2_NTM
gvrp enable
spanning-tree portfast auto
switchport mode trunk
SW version 4.1.0.1 (date 05-Apr-2012 time 15:03:04)

Gigabit Ethernet Ports
=============================
no shutdown
speed 1000
duplex full
negotiation
flow-control on
mdix auto
no back-pressure
spanning-tree
spanning-tree mode RSTP

qos basic
qos trust cos
eee enable
SCCM PXE server is fine, tested on Cisco gear. 
Tags (2)
0 Kudos
5 Replies

Re: 7048 Routing/DHCP relay with 5548

Jump to solution

Do you have an IP helper address set up on the 55xx switch?  Page 617 of the CLI Guide.

support.dell.com/.../en_ug.pdf

ip helper-address

Use the ip helper-address Global Configuration mode command to enable

the forwarding of User Datagram Protocol (UDP) broadcast packets received

on an interface to a specific (helper) address. Use the no form of this

command to disable the forwarding of broadcast packets to a specific (helper)

address.

Syntax

ip helper-address {ip-interface | all} address [udp-port-list]

no ip helper-address {ip-interface | all} address

Parameters

• ip-interface—Specifies the IP interface.

• all—Specifies all IP interfaces.

• address—Specifies the destination broadcast or host address to which to

forward UDP broadcast packets. A value of 0.0.0.0 specifies that UDP

broadcast packets are not forwarded to any host.

• udp-port-list—Specifies the destination UDP port number to which to

forward broadcast packets. (Range: 1–65535)

Default Configuration

Forwarding of User Datagram Protocol (UDP) broadcast packets received on

an interface to a specific (helper) address is disabled.

If udp-port-list is not specified, packets for the default services are forwarded

to the helper address.

Get Support on Twitter @DellCaresPro

Download the Dell Quick Resource Locator app today to access PowerEdge support content on your mobile device! (iOS, Android, Windows)

SHAFA4
Bronze

Re: 7048 Routing/DHCP relay with 5548

Jump to solution

Device connected to access port does get dhcp ip from the server without defining the ip helper address on 5548, IP dhcp relay enable is functioning, problem is with PXE, I already tried the above suggested with no luck. Smiley Sad

0 Kudos

Re: 7048 Routing/DHCP relay with 5548

Jump to solution

Do you have portfast set up on the interface trying to PXE?

Console(config)# interface gigabitethernet 1/0/15

Console(config-if)# spanning-tree portfast

In PortFast mode, the interface is immediately put into the forwarding state upon linkup, without waiting for the standard forward time delay.

Get Support on Twitter @DellCaresPro

Download the Dell Quick Resource Locator app today to access PowerEdge support content on your mobile device! (iOS, Android, Windows)

SHAFA4
Bronze

Re: 7048 Routing/DHCP relay with 5548

Jump to solution

This is weird, PXE start working when I hard code the fiber link between switches to full duplex, even though they are showing the full duplex in auto. Thanks for your help.

Re: 7048 Routing/DHCP relay with 5548

Jump to solution

I'm glad you figured it out.  Thanks for your contribution to the community.

Get Support on Twitter @DellCaresPro

Download the Dell Quick Resource Locator app today to access PowerEdge support content on your mobile device! (iOS, Android, Windows)

0 Kudos