voitsykh
1 Copper

M630 blade doesnt see brochade switch over FCoverEth

I have infrastructure

plan.jpg.

Problem: Brocade switch doesnt see wwn blade M630. Everything configured like in manuals.

More information:

A1#show fc switch
Switch Mode : NPG
Switch WWN  : 10:00:e4:f0:04:53:47:14
A1#show npiv devices brief

Total NPIV Devices =    0
-------------------------------------------------------------------------------------------------------------------

ENode-Intf      ENode-WWPN                FCoE-Vlan     Fabric-Intf     Fabric-Map      LoginMethod     STATUS
-------------------------------------------------------------------------------------------------------------------

A1#show fcoe-map

Fabric Name        fc-map1

Fabric Type        npiv
Fabric Id          1002
Vlan Id            1002
Vlan priority      3
FC-MAP             0efc00
FKA-ADV-Period     8
Fcf Priority       128
Config-State       ACTIVE
Oper-State         UP
=======================================================
Members
Fc 0/49 Fc 0/50 Fc 0/51 Fc 0/52
Te 0/1 Te 0/2 Te 0/16 Te 0/15 Te 0/3 Te 0/4 Te 0/5 Te 0/6 Te 0/7 Te 0/8
Te 0/9 Te 0/10 Te 0/11 Te 0/12 Te 0/13 Te 0/14 Te 0/17 Te 0/18 Te 0/19 Te 0/20
Te 0/21 Te 0/22 Te 0/23 Te 0/24 Te 0/25 Te 0/26 Te 0/27 Te 0/28 Te 0/29 Te 0/30
Te 0/31 Te 0/32
=======================================================
=======================================================

A1#sh int fi 0/52
FibreChannel 0/52 is up, FC link is up
Port is present
Pluggable media present, FC-SFP+ type is FC-8GBPS-SR
    Wavelength is 850nm
    SFP+ receive power reading is -2.5003dBm
Interface index is 1055110
MTU 2148 bytes
LineSpeed 8000 Mbit
Port type is N, Max BB Credits is 16
WWN is 20:34:e4:f0:04:53:47:1e, FC-ID is 010400
Last clearing of "show interface" counters 18:13:07
Statistics:
    BBCR_FrameFailures 0                    TotalRxBytes    2128
    BBCR_RRDYFailures  0                    TotalTxBytes    1584
    Class2FramesIn     0                    LongFramesIn    0
    Class2FramesOut    0                    LossOfSync      0
    Class3FramesIn     0                    ShortFramesIn   0
    Class3FramesOut    0                    RxLinkResets    0
    Class3Discard      0                    TxLinkResets    0
    DecodeErrors       0                    TotalLinkResets 0
    FReject            0                    TotalRxFrames   13
    FBusy              0                    TotalTxFrames   11
    AddressErrors      0                    RxOfflineSeq    0
    LinkFailures       1                    TxOfflineSeq    0
    InvalidCRC         0                    TotalOfflineSeq 0
Rate info:
    Input 0 bytes/sec, 0 frames/sec, 0.00% of line-rate
    Output 0 bytes/sec, 0 frames/sec, 0.00% of line-rate
Time since last interface status change: 18:11:37

Config from blade switch

interface FibreChannel 0/52
 fabric fc-map1
 remote-fault-signaling rx off
 no shutdown 

Screenshot from idrac

 1.png

Screenshot from idrac

2.png

 

 

 

 

 

Screenshot from chassis

4.png

5.png

 

Esxi:

6.png

 

San

7.png

Please, help.

Thx

 

0 Kudos
1 Reply
Anonymous
Not applicable

Re: M630 blade doesnt see brochade switch over FCoverEth

I would like to help look into this further. I have sent you a private message requesting some additional information. Looking forward to hearing from you.

0 Kudos