eldanba
1 Copper

Poweredge T110 II Memory issue

Jump to solution

Hi folks. I had a broken 2gb dimm

I thougt I buy one dimm of 8GB and replace all the other dimms

8gb Crucial Ddr3 1600 Udimm Pc (PC3-12800)
CAS 11
1.35V
NON-ECC
1600 MT/S
UDIMM

I put the dimm in the slot but the server does not boot up (i tried every slots)

Is that memory wrong ? I should be ECC only ?

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Moderator
Moderator

RE: Poweredge T110 II Memory issue

Jump to solution

Is it possible to run the server with only one 8GB dimm in one slot ? Or should I buy 2x4gb ?

A single DIMM is not a supported configuration, but it should work. A single DIMM configuration should only be used for troubleshooting.

Im trying to run the server with 1 dimm only and it's not working

If you are talking about the memory module you initially linked, it will not work in any configuration.

Daniel Mysinger
Dell EMC, Enterprise Engineer

0 Kudos
8 Replies
Moderator
Moderator

RE: Poweredge T110 II Memory issue

Jump to solution

Hello

Is that memory wrong ? I should be ECC only ?

The system only supports ECC memory. You can find the memory population rules in the manual.

Your system supports DDR3 ECC unbuffered memory modules (UDIMMs). The DIMMs can be 1066 or 1333 MHz. Single and dual-rank DIMMs can be 1066 or 1333 MHz.

1600MHz memory will work if it is capable of down-clocking to a supported frequency.

Thanks

Daniel Mysinger
Dell EMC, Enterprise Engineer

0 Kudos
eldanba
1 Copper

RE: Poweredge T110 II Memory issue

Jump to solution

Thanks a lot for your answer.

Is it possible to run the server with only one 8GB dimm in one slot ? Or should I buy 2x4gb ?

Im trying to run the server with 1 dimm only and it's not working

Thanks!

0 Kudos
Highlighted
Moderator
Moderator

RE: Poweredge T110 II Memory issue

Jump to solution

Is it possible to run the server with only one 8GB dimm in one slot ? Or should I buy 2x4gb ?

A single DIMM is not a supported configuration, but it should work. A single DIMM configuration should only be used for troubleshooting.

Im trying to run the server with 1 dimm only and it's not working

If you are talking about the memory module you initially linked, it will not work in any configuration.

Daniel Mysinger
Dell EMC, Enterprise Engineer

0 Kudos
eldanba
1 Copper

RE: Poweredge T110 II Memory issue

Jump to solution

thanks again for your answer. Im trying to troubleshot the originals dimms and im getting

Correctable and UNcorrectable ECC error BANK 1 DIMM A1

I cannot find anyplace with information on which one is BANK1  and DIMM A1...

How can i identify that dimm ?

Thanks!

0 Kudos
eldanba
1 Copper

RE: Poweredge T110 II Memory issue

Jump to solution

sorry. I just found out, is written on the motherboard

0 Kudos
eldanba
1 Copper

correctable ECC error bank 1 dimm a1

Jump to solution

Im getting this error in all the diagnostics tests.

I have 4x2GB dimms

I tried also with 2x2GB dimms in different banks than A1 but still I get the same error.

Can I do anything to fix it ? or is a motherboard problem ?

Tried many combinations and different dimms but always saying error in A1

Any suggestions ?

Thanks!

poweredge t110 II

0 Kudos
eldanba
1 Copper

RE: Poweredge T110 II Memory issue

Jump to solution

Can I put 3x2GB total 6GB to run the server... Using 3 memory slots ? Or I need to put in pairs ?

Thanks a lot

0 Kudos
AymanIT
1 Copper

Re: correctable ECC error bank 1 dimm a1

Jump to solution

I HAVE the same issue correctable ECC error when test ram memory also i have an error on ESXI ram warning 

0 Kudos