Skip to main content
Start a Conversation

Unsolved

This post is more than 5 years old

donofaneage

1 Message

52929

October 15th, 2015 14:00

Dell 4320

I have a Dell 4320 projector...The bulb light was solid and the power light was blinking. Replaced the bulb and it still won't power on and now the bulb light and temperature light are solid orange and the power light still blinks orange. I tried looking through the manual but I don't know what could be the issue. Anyone ever encountered this or have any suggestions?

DELL-Jesse L

Moderator

 • 

16.7K Posts

October 27th, 2015 08:00

donofameage,

Below is troubleshooting information for the 4320 projector.

The following table lists the common lamp-related problems  and their  possible solutions.

Problem Solution
The lamp is burned out or  makes a popping sound. When the lamp reaches its end of life, it may            burn out and may make a loud popping sound.             If this occurs,  the projector does not turn back          on. You need to replace the lamp.
The lamp light is solid amber. If the lamp light is solid amber, replace the          lamp.
The lamp light is blinking amber. If the lamp light is blinking amber, the lamp            module connection may be disrupted. Check the lamp module and ensure that it is            properly installed.
            If the lamp and  power lights are            blinking amber, the lamp driver has failed and            the projector will automatically shut down.
             If the lamp and temperature lights are blinking            amber and the power light is solid blue, the            color wheel has failed and the projector will            automatically shut down.
            To clear the projection mode, press and hold          the Power button for 10 seconds.
The temperature light is  solid amber. The projector has overheated. The display            automatically shuts down. Turn the display on            again after the projector cools down. If the          problem persists, contact Dell Inc.
The temperature light is  blinking amber. The projector fan has failed and the projector            will automatically shut down. Try to clear the            projector mode by pressing and holding the             Power button for 10 seconds. Please wait            for about five minutes and try to power up again. If the          problem persists, contact Dell Inc.

 Status Light Diagnostic Matrix

Compare the LEDs on the unit with the matrix details in the  following table to determine the possible cause and solution for a projector  issue.

Guiding Signals
Projector           status
Description
Control button
Indicator
Power
Temp (Amber)
Lamp (Amber)

Standby mode

 The projector is in the Standby  mode and ready to power on. BLUE           Flashing OFF OFF
Warming up          mode The projector takes some  time to warm up and power on. BLUE OFF OFF
Lamp on

The projector is in the Normal  mode and ready to display an image.

A NOTE indicates important information that helps you make better use of your computer. NOTE:                   The OSD menu is not accessed.

BLUE OFF OFF
Cooling mode The projector is cooling to  shut down. BLUE OFF OFF
Cooling before Power Saving          mode The projector takes 60 seconds to cool down before entering Power Saving mode. 
AMBER OFF OFF
Projector           overheated If the air vents are  blocked or the ambient temperature is above 35ºC, the projector automatically  shuts down. Ensure that the air vents are not blocked and that the ambient  temperature is within the operational range. OFF AMBER OFF
Lamp driver           overheated If the lamp driver is  overheated or the air vents are blocked,  the projector automatically shuts  down. Turn the display on again after the projector cools down. AMBER AMBER OFF
Fan breakdown If one of the fans has  failed, the projector automatically shuts down. OFF AMBER           Flashing OFF
Lamp driver           breakdown If the lamp driver has  failed, the projector automatically shuts down. Unplug the power cord, and  then, after three minutes, turn the display on. AMBER           Flashing OFF AMBER Flashing
Color wheel           breakdown If the color wheel cannot  start, the projector has failed and it automatically shuts down. Unplug the  power cord, and then, after three minutes, turn on the projector. BLUE AMBER Flashing AMBER Flashing
Lamp failure The    lamp is defective. Replace the lamp. OFF OFF AMBER
Fault - DC          supply (+12V) If the power supply has  been interrupted, the projector automatically shuts down. Unplug the power cord,  and then, after three minutes, turn on the projector. AMBER           Flashing AMBER AMBER
Lamp module             connection          failed The lamp module connection may be            disrupted. Check the lamp module and          ensure that it is properly installed. OFF OFF AMBER           Flashing

View More

View All

No Events found!

Top