UNSOLVED

rob-f

updated

4 months ago

RF

rob-f

1 Rookie

•

3 Posts

•

10 Points

0

396

June 29th, 2026 15:30

Switching storage from RAID to AHCI in order to update Samsung SSD 990 PRO

I own a Dell Tower Plus system running Windows11. I have 3 SSD installed in the system: the Micron 2TB SSD provided by Dell, one Samsung SSD 990 PRO 2TB installed by me on the mother board, one Samsung SSD 990 PRO 4TB installed by me on a PCI card. I would like to update the firmware of my two Samsung SSD. Magician is not able to do this due to the fact that the storage is configured (as delivered by Dell) as RAID. I have made several tries to boot on USB keys based on information provided by Samsung (with secure boot off and storage AHCI) without succes: impossible to boot (nothing happens). The last recommendation I got from Samsung is to configure the system in AHCI mode "after asking to the supplier of my system how to do this". I saw several post on Internet explaining how to do this (booting in safe mode after changing the BIOS from RAID to AHCI) without loosing anything - which is my goal. Is this the correct way to go ? I'm a little worried by what would happen if something goes wrong ...

Thanks in advance for advice.

  • ejn63

    12 Elder

    •

    31802 Posts

    •

    156136 Points

    1

    0

    Posted June 29th, 2026 16:45

    If there is a setting for AHCI (RAID OFF), yes this is the way to proceed.  That said, many new systems come with only IRST as the default, and do not have AHCI (RAID OFF) mode.  Go into setup (F2 at powerup) and then to SATA/NVMe operation.  If there is a RAID OFF setting, that should solve the problem.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    0

    0

    Posted June 29th, 2026 18:53

    Interesting that you have a newer Dell Tower Plus and it shipped with it in RAID-mode instead of AHCI-mode (BIOS switch).

     

    That usually means Intel-RST and/or Intel Optane Memory and Storage Management is installed inside Windows. AFAIK, both/all of these programs/drivers are legacy and have been depreciated. 

    Personally, I've always hated them ... and have been known to completely re-partition and clean-install-Windows to get rid of them. IMO, they haven't been needed in over 10 years when SSDs came on the scene (SATA and now NVMe).

     

    To get all this foundationally re-aligned, it's now part of my clean-install directions:

    Verify computer passes ePSA-Diagnostics (outside of Windows).
    NVMe-SSD should be "DiskPart cleaned" back to un-initialized/raw.
    BIOS set to UEFI-Mode and AHCI
    - Some users report that SecureBoot needs to be OFF during actual Windows install, but I always leave it ON.
    Only that one SSD installed/connected for now
    F12 on boot to boot USB-FlashDrive from microsoft.com Media Creation Tool
    https://www.microsoft.com/en-us/software-download/windows11
    Install Windows to un-allocated/un-partitioned space
    - It will initialize the NVMe-SSD as GPT, and format as NTFS
    Refrain from installing any drivers from support.dell.com (ie, no "heavy" Dell Utilities or Intel driver-suites)
    - Maybe Intel-Chipset (if your computer is very new) otherwise ...
    - - Try to get all drivers from Windows-Update (including Advanced/Optional area) and nvidia.com 
    - I don't use SupportAssist. 

    You do this to see if "the hardware" is good after-all.
    After your Device-Manager is clean, you should be able to re-enable SecureBoot if you disabled it earlier during initial install.

    Notes:
    1. If semi-forcing Windows-11 onto an older (non- UEFI) Legacy BIOS computer, the Windows installer might decide to Initialize the main drive as MBR instead.
    2. While sometimes not obvious, it IS still possible to install Windows with only a Local (Admin) Account.
    3. An Alienware computer might need AW-CC from Dell, but that should be about it.
    4. Support-Assist, Dell-Update, and/or Alienware-Update ARE NOT required for Windows-11 to run programs, apps, or games. 
    5. With BIOS set to AHCI, in Windows never install Intel-RST or Intel Optane Memory and Storage Management.
    6. Now-days, your Windows-Key is embedded in BIOS-Firmware. Still, it does not hurt to retrieve it and know it.
    7. Non-OEM Windows-11 should still see the Key and Authenticate as Legit.

    (edited)

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    0

    0

    Posted June 29th, 2026 19:07

    As for Samsung Magician:

    a. Be sure you are running the latest version. I'm currently running 9.x (for my two retail 990-Pro-2tb-NVMe's and my 4tb=T7-Shield). I have other Samsung SSDs in other computers (been buying them for like over 10 years now).

    b. In the old-days ... Samsung would blame various poor low-level communications with their drives on the AHCI thing. Usually they were correct, but sometimes is was actually a different reason. I don't remember the real reason, but it was something obvious.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • rob-f

    1 Rookie

    •

    3 Posts

    •

    10 Points

    1

    0

    Posted June 30th, 2026 06:44

    @Tesla1856​ Thank you for your answer. I'm running Magician 9.0.1.

  • rob-f

    1 Rookie

    •

    3 Posts

    •

    10 Points

    0

    0

    Posted June 30th, 2026 06:54

    @ejn63​

    Thank you for your answer. There is indeed in my BIOS an AHCI/NVMe option.

    I've found this procedure in a (Dell community) post labelled "How to Boot after Changing from RAID to AHCI":

    1. Run cmd as administrator
    2. Copy-paste this command, which will start Windows in SafeMode Mode the next time you reboot:
    bcdedit minimalbcdedit /set {current} safeboot minimal
    3.Restart the computer and enter UEFI/BIOS setup.
    4.Change the SATA operation mode from RAID to AHCI.
    5.Save changes and exit Setup and Windows will automatically boot boot to Safe Mode.
    6. Launch cmd again, as in step #1.
    7. Copy-paste this command, which will start Windows in Normal Mode the next time you reboot:
    bcdedit safebootbcdedit /deletevalue {current} safeboot
    8. Reboot and Windows will automatically start with AHCI drivers enabled.

    Does this apply also to NVMe ? It is a correct and safe way to proceed without loosing anything ?

    Thanks in advance for your answer.