UNSOLVED

craig.young

updated

12 years ago

0

47478

July 24th, 2014 08:00

U2414H, vertical line of dark pixels on the screen

model - U2414H
serial number - CN- 0R9F1P-74621-3BM-1PML
revision number - A00
specific computer model - Microsoft Surface Pro 2, 8MB RAM, 256 GB HDD
operating system - Windows 8.1 Pro
video card - Intel HD Graphics 4400
What video out ports are available on the video card? - DisplayPort
What video out port are you using from the video card to what video in port on the monitor? - Surface Pro 2 DisplayPort out --> 1st Dell U2414H monitor DisplayPort in --> 2nd Dell U2414H monitor (the one with the vertical line issue) mini DisplayPort in using Dell supplied video cables and monitors set to DisplayPort 1.2 enabled.
What cable are you using to attach the video card to the monitor? - Dell supplied DisplayPort to mini DisplayPort cable
Press the monitor Menu button to open the monitor OSD (On Screen Display). The bottom of that screen should show a resolution. That resolution should match the monitor default resolution - resolution set to 1920x1080 60Hz, which matches the monitor's default resolution
Can you post a video of the issue? - not at this time
Full description of the monitor issue - Hello, I have a U2414H monitor that has a vertical line of dark pixels showing up on the screen. The pixels extend from the top of the screen to the bottom. I've tried restoring the monitor to Factory Defaults using the OSD and I've run the monitor Self-Test and BID, all to no avail on correcting the issue. My current configuration is a Microsoft Surface Pro 2 connected to a dual monitor setup (2 of the Dell U2414H monitors) using the Surface's DisplayPort video output to connect the monitors in a DisplayPort 1.2 daisychain. The monitor that is having the issue is the secondary monitor at the end of the daisychain. I'm using the Dell supplied cables and have the monitors setup with DisplayPort 1.2 enabled. Any thoughts on a possible fix for this issue, or do I have a bad monitor that needs to be returned to Dell for a replacement? I purchased the monitors in January 2014 and bought them directly through Dell's website. I look forward to a response, thanks!

-Craig Young

  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    1270

    0

    Posted July 24th, 2014 10:00

    Great posting! The Self-Test and BID (Built-in Diagnostics) are independent of the computer and cabling. IF you see the v-lines when running the Self-Test and BID, the monitor is faulty. Read this for 24" monitor exchange instructions.


    DELL-Chris M (old account)

    #IWork4Dell

  • 1270

    0

    Posted July 24th, 2014 10:00

    Thanks for the response, Chris M. The monitor in question is in a remote office (e.g., I don't have direct contact with it) so I'll confirm that the v-lines are there during the self-test and BID runs. Out of curiosity, if the lines are NOT there during the test, what would be causing the issue during normal operation? -Craig
  • DELL-Chris M

    Community Manager

    •

    56891 Posts

    •

    232143 Points

    1270

    0

    Posted July 24th, 2014 18:00

    I would have them test the problem secondary U2414H as a standalone primary using the same current hardware. That would take the DP (DisplayPort) MST daisy chain out of the troubleshooting. If the v-lines do not appear, then connect the other U2414H as the secondary and see if the v-lines then appear on the secondary.


    DELL-Chris M (old account)

    #IWork4Dell

  • 1270

    0

    Posted July 25th, 2014 06:00

    Thanks for the follow-up Chris. I actually had my staff person try this exact procedure prior to my posting in this support forum! I was trying to see if it was a cable issue, or a hardware issue with the Surface. Unfortunately, the v-line stayed put on the problem monitor under each scenario. Thanks again for your help, I'm going to call Dell Customer Support later today to initiate the return. Cheers! -Craig