Usually you need NMDA installed and registered with local nsrladb and nsrauth enabled on both points of communication. I don't use wizard, but these were some generic requirements for wizard to work.
From what I see nsrdb2ra -i fails (perhaps user@hostname is needed for wizard to work?). I assume one could try to debus as to why it fails or simply revert to manual steps as claimed in quoted docs (if not documented in install guide, then contact support for those steps).
ble1
4 Operator
•
14.3K Posts
0
October 6th, 2014 08:00
Did you read NMDA installation guide? I would also suggest to use 1.5 at least.
JayJay9882
2 Intern
•
161 Posts
0
October 7th, 2014 05:00
Ok, I see.
What do I need to do to get the DB2 option in the client wizzard? So far I just get this:
ble1
4 Operator
•
14.3K Posts
0
October 7th, 2014 05:00
Linking is done in Oracle environment. In DB2 you need to unset vendor ini pointers (see page 34 of installation guide).
JayJay9882
2 Intern
•
161 Posts
0
October 7th, 2014 05:00
I just did. I don't see any differences to the 1.2 when it comes to linking the NMDA module to the database environment.
Linking is for me something like doing "ln -s blablubb". I don't need to do this for an DB2 instance?
ble1
4 Operator
•
14.3K Posts
0
October 7th, 2014 08:00
Usually you need NMDA installed and registered with local nsrladb and nsrauth enabled on both points of communication. I don't use wizard, but these were some generic requirements for wizard to work.
bingo.1
2.4K Posts
0
October 8th, 2014 04:00
Sorry - too early. I though you were already running restores.
The issue obviously is that the NW client does not recognize the capabilites.
Did you restart the NW client daemon (nsrexecd) ?
JayJay9882
2 Intern
•
161 Posts
0
October 8th, 2014 04:00
Couple of times!
Do I need to configure the NMDA config file yet?
bingo.1
2.4K Posts
0
October 8th, 2014 04:00
Did you configure you DB2 client resource yet and run a hot db backup?
JayJay9882
2 Intern
•
161 Posts
0
October 8th, 2014 04:00
Done that!
Still no DB2 option within the wizard.
Can someone else provide help?
Cheers
Jan
JayJay9882
2 Intern
•
161 Posts
0
October 8th, 2014 05:00
I updated to NMDA 1.6 and after the installation I get this:
Preparing... ########################################### [100%]
1:lgtonmda ########################################### [100%]
42503:nsrdb2ra: Program not registered
Automatic wizard registration command /usr/sbin/nsrdb2ra -i failed.
Please refer to documentation for manual steps.
bingo.1
2.4K Posts
0
October 8th, 2014 05:00
yes - as only Informix, Oracle and Sybase have restrictions. exceptions.
However, IMHO the wizard should already recognize that the NMDA software is in place.
bingo.1
2.4K Posts
0
October 8th, 2014 05:00
Due to missing documentation it is not so easy to quide you as the CLI Refence clearly states:
The nsrdb2ra command should not be run on the command line without instructions from NetWorker Customer Support.
JayJay9882
2 Intern
•
161 Posts
0
October 8th, 2014 06:00
Oh man, EMC at its best!!!
Can you tell me quickly, where did you find this?
bingo.1
2.4K Posts
0
October 8th, 2014 06:00
You will find it in the NMDA Command Line Reference
ble1
4 Operator
•
14.3K Posts
0
October 8th, 2014 23:00
From what I see nsrdb2ra -i fails (perhaps user@hostname is needed for wizard to work?). I assume one could try to debus as to why it fails or simply revert to manual steps as claimed in quoted docs (if not documented in install guide, then contact support for those steps).