Search Results (3.1K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Added a second CPU to a T440, original was Xeon Silver 4110, new (secondary) one is Xeon Gold 6138.Boot thew this error: "CPU Error Invalid or unsupported Topology between CPUs detected. Please replace CPUs and pupulate in a supported configuration." Tried to swap, no luck either.Have not found anyt
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello!We would like to install NVIDIA RTX A5000 in Dell R7515.Please tell us the DP/N of a suitable cable install kit so that we can order it.Thank you!
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello everyone, I have recently purchased a T430 and I plan to install a Tesla V100 GPU. The PSU board has two 8pin CPU connectors and the V100 also has 8pin CPU connector. I have checked the V100 GPU pinout and looking at the connector itself. Top 4 pins (Pin 5-8) are 12V and the bottom 4 pins (Pi
Question
•
PowerEdge Hardware General
Community Accepted Solution
This is my first post here. . . I recently acquired a PowerEdge T430 that I plan to use for home use. I was planning to use the Trusted Platform Module (TPM) 2.0, which was not previously installed. However, I'm having trouble locating the correct part number for the module/kit. I've located the par
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello. I noticed that updating the iDRAC in my PowerEdge R7525 to the 7.x releases, that picture that shows the front of the server with the drive bays populated under Storage doesn't appear anymore. If I roll back to 6.10.80.00 it's there. Was this removed from iDRAC 7.00.00.00 and above? I couldn
Question
•
PowerEdge Hardware General
Community Accepted Solution
Dear Sir or Madam,I have bought the Poweredge R730 w/ Single E5-2640 V4 (10C/20T) with 750W 80+ Platinum PSU config and perform well. Now I wish to add the GPU card for extended processing performance, eg. GTX1080 with typical 170W. I have searched the Dell community and external forums and found th
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have an r730xd with motherboard part number 4N3DFand an r730 with motherboard part number 599V5Some things I've seen say that you must replace the motherboard with the exact one, others say that these two part numbers are compatible.If I had a 4N3DF in stock as a spare would it work in the r730 as
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi, I have a question about the DELL T40 mini server. I would like to replace the processor in it because 4 cores and 4 threads are not enough. Does anyone know what processors can be installed in it? I know that the documentation says that it only supports this processor (E-2224G) but maybe som
Question
•
PowerEdge Hardware General
Official Solution
Hi to all Dell team, we have an R640 server that has an issue of (the System Board fail-safe voltage is outside of range), no power, I tried to swap and replace the power supplies but nothing, the server still off and couldn't turn on, I did the reset step (30 seconds hold on the power button)
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello guys, Recently, I'm trying to update the iDRAC version to a new one using RACADM tool on a Dell R740 server. The RACADM tool that i chose is version 9.2.0. The iDRAC will be updated from version 5.00.00.00 to 5.10.00.00 The client that runs the RACADM tool is a windows 10 computer and the iDRA
Question
•
PowerEdge Hardware General
Community Accepted Solution
I just purchased a DELL T360 (outlet). The unit supports 4 drives. The purchase is just an expensive toy. At some point would it be possible to get an upgrade kit to support 8 drives. I am planning on using it as an iternal media server/backup storage for ph
Question
•
PowerEdge Hardware General
Community Accepted Solution
I recent have been tasked with upgrading the Server here at our office and was wondering if I could use the same heatsink G70XM 0G70XM that is for CPU 1 or is it a completely different part number. such as 01CW2J 1CW2J. please advice.
Question
•
PowerEdge Hardware General
Official Solution
What is the power consumption for a dell server R6625 with 2 PDU 1.8w
Question
•
PowerEdge Hardware General
Community Accepted Solution
Official Solution
Hi all, I need help to add 2 GPU NVIDIA H100 PCIe in server DELL PE R760xa, can somenone share all components that I need to use to make this happend ? Thansk a lot .
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi, We have a DELL R910 server (Service Tag:<ADMIN NOTE: Service tag removed per privacy policy>) and have read some articles here about the problem "E1234 Memory Riser Power Failure" . We have done some of the suggested troubleshooting. On our system, here's what we've done so far: 1
Question
•
PowerEdge Hardware General
Official Solution
Hello, I was gifted a Dell R7525 8 Bay server and was wondering if the chassis was Dell or OEM. What's the easiest way to know for sure? One of the lines on the service tag says: "PowerEdge R7525 CE and CCC Marking". What does that mean? Thank you
Question
•
PowerEdge Hardware General
Official Solution
Dear Dell Support, I am encountering an issue with my Dell PowerEdge R200* server. No matter which version of Windows I install, including *Windows Server 2019*the server does not recognize the graphics card. I even installed a separate discrete graphics card, but the issue persists. Could you plea
Question
•
PowerEdge Hardware General
Community Accepted Solution
We experienced a power outage here, and now the Server (Dell T320, Windows Server 2012) won't start. I ran a hardware check using Dell’s Lifecycle Controller, and no errors were reported. The server has two AHCI-configured drives, and the BIOS hasn’t been updated. Could you help me figure out whethe
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello,I have a task. I need to buy R760 but I don't know which chassis to choose. I need a server with two BOSS disks with Raid 1 (for operating system) and also two separate raid arrays. First HDD array with 6 disks (raid 5), and second array with two NVME disks (raid 1). 2 CPU required. Please hel
Question
•
PowerEdge Hardware General
Official Solution
Hi All, I would like to ask maybe someone have experience with this NVMe disk (DELL 1.6TB NVME PCIE HHHL 0TWFTD) and server R730xd. I'm thinking about add this disk to my lab server, but I'm not sure that will work. Regards
Question
•
PowerEdge Hardware General