Search

I have a PowerEdge R7525 server with two failed hard drives that were part of a RAID 5 setup. It's currently showing Dell's Device Health Manager. I would like to shut down the server so I can remove the failed hard drives, but I can't seem to leave the Device Health Manager. When I hit the exit but

How I can fi x this problem

Im upgrading an R930 from the four hdd sff to 24 hdd sff. The front bezel is not compatible and has to be changed. Problem is how does it come off? Are the rack ears holding the bezel on somehow? I tried to take the ears off but theyre on there with either security screws or some screw head type Ive

I have Dell PowerEdge R730 and R620 series servers, each equipped with multiple add-on NICs. When booting in Legacy PXE mode, the system only attempts PXE boot from the first NIC in the boot order and ignores the remaining interfaces. Since I often don’t know in advance which NIC will have an active

hey everyone, I don't know why I am getting this message on my server     RAC0654: No operations can be performed on the iDRAC Service Module. Make sure that the iDRAC Service Module is installed on the server operating system and then retry the operation.  Please someone helps ? Tha

I have a Poweredge R540 rack server that has (2) virtual arrays: 1 is (2) x 256GB SSD in RAID1 for the OS, then a RAID5 Array for Storage (This is being used as a camera surveillance server) It will not boot into Windows. I get "No boot device available . Current boot mode is set to BIOS. Please en

I am looking to active lldp on idrac 8 server R630 and R730. I have tried the commands below and they all failed. I am unable to find the option in the iDRAC gui to manually modify the configuration. Failed Racadm config -g cfgLanNetworking -o cfgNicEnable 1failed racadm set /System/Network.LLDP.E

Hello, i'm reaching out for help as i'm at a bit of a loss here. We've recently bought a total of 6 Dell PowerEdge R320 servers for a small service cluster. As per our internal policy we must perform a full hardware diagnostic run before even starting to do tests in the server room. The issue i

Hello, I used OME to update the firmware on an R750 2 days ago. I verified on the iDrac that the firmware was updated to the latest version. The OME job completed successfully. When I look at the R750 now in OME, it still shows the same list of firmware updates are available. I've tried running Disc

Hi! So i have this MD1420 enclosure that has worked fine for 7+ years, but it has run out of service now. However i still want to use it a bit for something else, so i moved the H830 raid controller from the server it was connected to (an R630), and connected it to another R640. It seems to work fi

How does Dell structure it's parts commonality amongst the PowerEdge units? Are the commonality in the generation? For instance; would R930's share parts with Rx30's or R9xx units. I have a bare bones R930 with the four bay hdd drive sff. Im upgrading it to the 24 bay sff set up. I dont know which p

Mi servidor Dell Power Edge R430 se reinicia solo y aparece un mensaje de bateria descargada o desconectada. Si la reemplazo se pierde la configuracion de los discos duros?

Hello, I have a PowerEdge R330 server currently running BIOS version 1.4.3. I'm trying to update it to the latest version (2.20) using a USB drive. The USB is formatted as FAT32, and the update .exe file is in the root of the drive. However, when I try the update, I get this error: Unable to verif

We have a PowerEdge C6620 with a 1x Intel E810-XXVDA4 Quad Port 10/25GbE SFP28 Adapter, OCP NIC 3.0 using Dell 10/25Gb Transceivers connected to a Cisco 9300 using Cisco 10Gb SFP+ Transceivers. I am unable to configure the system to allow the Layer 1 to come up during boot. I can get the ports to l

I removed all of the DIMMs from my R820 and tried replacing them with higher capacity ones, but then realized they were not compatible with its DIMM slots. I removed the incompatible ones and put back in the original DIMMs, but now when I turn the R820 on, it says "Fatal error! No memory detected!".

Bought this as a learning experience. Bought a cheap but reputable unit online and have started working on it. It's spec'd as what Id label as a bare bones system -less than. It's configured with none of the hardware or cables to actually have it work. Its only hdd bays are 4 in the front with blank

Will the Dell 80G5N or the Dell 23PX6 work in the R730XD while maintaining proper idrac fan control? I am currently using amazon PCIe M.2 Adapters, and while they do work, I lose all automatic fan control, and I'd rather keep my full fan control( I know I can turn it off with IPMItool), These are

I know how to disable boot devices in the UEFI boot sequence section of the BIOS, but the documentation doesn't address removing entries.Is it possible?If so, where is it dealt with?

PERC H730P Mini When replacing two disks that were about to fail I did the big mistake to replace the 2nd one before the 1st one was finished rebuilding. So it crashed, and i have to reinstall the whole thing.  So out of 8 disks the two that were physically replaced have state Foreign now. I

I always get this error from the same device iDRAC Message Event occured for Device Name !!!!!!!!!!, Device ip address !!!!!!!!!!, Service Tag !!!!!!!!, UTC time: 2025-04-03 11:1825, Severity: warming, Message ID : CDEV9000, This device and several others has become non compliant after running compl