Search

I have a PowerEdge e1000m chassis with multiple PowerEdge M620 servers. One server (server-1) is inaccessible through the iDRAC web interface because its NIC is set to Share mode, blocking remote access to its management IP. No operating system is installed on that server yet. I’m using CMC version

Never had bitlocker set up but my computer is asking for a key, what do I do?

S/N: CN-0RVC21-74261-38V-2HFU

Ciao a tutti. Avrei necessità di riesumare questa macchina ma con Windows server 2019 in quanto il 2016 non va bene per le applicazioni necessarie. Qualcuno ha conferma che è possibile installare il 2019? Grazie mille.

The integrated graphics card is starting to have issues. The display is showing a blue color and it wont accept video resolutions that used to work fine in the past.  When I bought the T440 many years ago I installed a PCI graphics card in it, but the system doesn't see it.  Unfortunately

Monitor: U3011, purchased about 2 weeks ago Revision A08 SN MX-078W52-74446-2B2-A0TL The problem I have since unpacking is the monitor is leaning noticeably to the right when placed on a flat surface. I measured the right edge is about 4mm lower to the table than the left.  Is there some pr

Just unboxed this beast from Best Buy and in getting everything running, came to this forum to read about problems. I attached CPU-Z because I read that you can not add regular HyperX memory to the R9 because of the higher voltage requirements of the Alienware brand HyperX memory. CPU-Z shows it r

Looking for a web based or Windows software of open manage to reconfigure raid rather than reboot or command line perc commands

Hello, after a sever reboot and loss of configuration, the server lost its idrac license and doesn't even have express. I have re-registered the server under us transferred ownership. It's an older R320. Unfortunately I have nothing in digital-locker. How should I proceed? Thank you.

0W1GCR // Broadcom NetXtreme II 10 GB- 2 port - PCI Express x8 // I need to know if it is compatible with the POwerEdge R250 r250 server

I have a PS6110 outside of a maint contract and I'm trying to upgrade to 10.0.3 firmware but the upgrade stops at 97% each time. The system is showing no active errors when upgrading but I do occasionally see a "flash card write failed after maximum number of retries exceeded" error in the logs.&nb

Other than the backplane (N9YVX) do I need completely different nodes or can I just get a server card (VNFMF) and a cable (X50KP) for each node? Thanks!

I'm trying to figure out which card I need for an ML3. As far as I can tell one of these should work: QLE246x FC QLE26xx FC  BR8x5 FC  It would go in an R740 or R750. Anyone have any ideas?

Hi just a little warning for everybody having a T140 with an additonal PCIe graphicscard (AMD RX6500XT) After Upgrading to BIOS 2.19 the T140 stopped booting when my LG 29 in Monitor was connected via Displayport. In the iDRAC it was just mentioned that the boot process was stopped from BIOS. Afte

Hello, As the subject states, I am trying to connect a PowerVault MD1400 to OpenManage Enterprise 3.10. The server to which it is attached has been discovered and displays all information from the server side without issue. The issue is when looking at the Update Firmware page in OME, all of the dr

Hi Team We are receiving critical vulnerabilities (CVE-2024-25943) related SSH version in Idracs 9 that already are in the last firmware version. ( 7.00.00.181, 7.20.30.55) seems the only way to fix this is upgrading SSH version to 10.0 , bus as I said all iDRACs have the last version, Do you know i

Hi guys, Kindly looking for some support with an issue I'm running into with my R6515 10 Bay NVMe server. I'm utilizing an Intel E810-XXV Dual Port 10/25GbE SFP28 PCIe adapter (CD16M) and running into some errors.  Typically happens when PXE booting fails.  "A bus fatal error was detected

Today, I update 7760 with BIOS v1.10.1. First, I download and excute .exe file, but get error message "Unable to lauch UI module". Then, I download and save .rcv file into a USB key and perform following steps, shutdown, unplug the power cable, press ESC and Ctrl simultaneously, plug the power cable

Request for Unlocking Quotes for BIH During the preparation of our tender dossier, we have encountered a situation where information has been leaked. To ensure transparency and fairness in the bidding process, BIH requests that Dell unlock all Purchase Orders (POs) listed under the name EU as BIH.

Hello all, I have installed the SCG application and added a few PowerEdge iDRACs. Also I have installed ISM agents on the servers. The devices are shown as connected and their monitoring is enabled in SCG. So they seem to be fine. Now I need to ensure if the automatic case creation works as expecte