How Do I Connect My Dell W5300n Printer Directly to My Network? - KB Article - 171861

How Do I Connect My Dell W5300n Printer Directly to My Network? - KB Article - 171861




Connect the W5300n Printer Directly to the Network

  1. Verify that the printer is turned off and is unplugged from any power sources.

  2. Connect a Category 5 (CAT5) network cable to the Ethernet port on the back of the printer (Figure 1).


    Ethernet Port
    Figure 1 - Ethernet Port

NOTE

NOTE: The printer will automatically adjust for the network speed.

  1. Connect the power cable to the printer and to a grounded outlet.

  2. Power the printer on.
    After the printer completes its internal test, the Ready/Data light appears.



Print the Network Setup Page on the W5300n Printer and Check the Network Settings

  1. After the Ready/Data light has stopped blinking, press and release the Continue button to print the Menu Settings and Network Setup pages.

  2. Under the Standard Network Card heading on the Network Setup page, ensure that the Status is listed as Connected.

  3. Locate the IP address located under the TCP/IP heading. If the IP address equals 0.0.0.0, wait a few minutes and print the Network Setup page again.



Configure the Print Queue for the W5300n Printer

  1. Click the Start button.

  2. Click the Run button.
    The Run window appears.

  3. In the Open: box, type the following text:
    X:\setup.exe
    where X is the letter of your CD drive.

  4. Click Install the printer on the network.
    The Dell W5300n Laser Printer Installation window appears.

  5. Click the Next button.

  6. Click the server or system name that will share the printer with other computers.

  7. Click the Next button.

  8. Click to select Install the software and Install the User's Guide on the server.

  9. Click the Next button.

  10. Click to select Share the printer on this server.

  11. Create a share name you want to use for the PCL driver and PostScript driver.

NOTE

NOTE: Make the share name obvious so the clients can easily find the printer when browsing for shared printers.

  1. Click the Next button.

  2. Verify that Choose an existing port for the printer connection is selected.

  3. Select the port that corresponds to the hardware port selected when the printer was connected to the server.

  4. Specify a port name.

  5. Type in the printer IP address.

  6. Click the Finish button.

  7. Print a test page to ensure that the software is correctly installed.

  8. Click the Finish button to exit.



Install the W5300n Network Printer Drivers for All Clients

  1. Click the Start button.

  2. Click Printers and Faxes.
    The Printers and Faxes window appears.

  3. Click to highlight the W5300n printer listing.

  4. Click File.

  5. Click Sharing.
    The Dell W5300n Laser Printer Properties window appears.

  6. Click the Sharing tab.

  7. Click to select Share this printer.

  8. In the Share name: box, enter the name of the share if one does not appear.

  9. Click the Additional Drivers button.
    The Additional Drivers window appears.

  10. Select the operating systems of all network clients printing to this printer.

  11. Click the OK button.

  12. Click the Apply button.

  13. Click the OK button.



Dell™プリンタの詳細情報

この文書で提供される情報以外のサポートについては、Dell Supportのテクニカルサポート担当者にE-メールまたはチャット で問い合わせることができます。



 
Quick Tips(クイックヒント)の内容は、問題を日々解決するDellサポート担当者によって公開されます。 迅速な公開を実現するため、Quick Tipsは部分的な解決策や対処方法のみを示すことがあり、これらはまだ開発段階であるか、問題を無事解決できることを裏付けるさらなる検証を保留中のものです。 こうしたQuick Tipsは、Dellが確認、検証、承認をしていないため、適切に注意して利用する必要があります。お客様がQuick Tipsにある手順やアドバイスに従うことにより被るデータの喪失、利益の損失、収入の損失などの一切の損失について、Dellは責任を負いません

記事ID: SLN17883

最終更新日: 2010/12/07 00:00


この記事を評価する

正確
有益
分かりやすい
この記事は役に立ちましたか?
はい いいえ
フィードバックをお寄せください
コメントでは、以下の特殊文字は利用できません: <>()\
申し訳ありませんが、フィードバックのシステムは現在ご利用いただけません。後でもう一度試してください。

フィードバックをありがとうございます。