기술 문서

How do I set up a Spanning Tree configuration on a Dell™ PowerConnect™ 3024 or 5012 managed switch? - KB Article - 155829


How to set up a Spanning Tree configuration on a Dell™ PowerConnect™ 3024 or 5012 managed switch using terminal services.

Set up a Spanning Tree configuration by performing the following steps:

  1. Connect to the switch.
    NOTE: For more information on connecting to your switch, click here.
  2. Select Spanning Tree from the main menu. (Figure 1)


    Figure 1


  3. To configure spanning tree settings that will affect all ports, select Bridge Settings. (Figure 2)


    Figure 2


  4. Configure the necessary settings or disable spanning tree altogether. (Figure 3)


    Figure 3


  5. Press the <Ctrl> + <W> keys at the same time to save the changes to NVRAM. (Figure 4)


    Figure 4
  6. To configure spanning tree settings for a specific port, select Port Settings. (Figure 5)


    Figure 5

    NOTE:
    Figure 6 shows the spanning tree settings for each port.


    Figure 6


  7. Make the necessary changes and save them to NVRAM.



Set up Spanning Tree on a Dell™ PowerConnect™ 3024 or 5012 from a web browser.

Set up a Spanning tree configuration by performing the following steps:

  1. Connect to the switch.

    NOTE: For more information on connecting to your switch, click here.

  2. Select Spanning Tree.
  3. To configure spanning tree settings that will affect all ports, click Bridge Settings and configure the necessary settings.

    NOTE: You can also disable Spanning Tree all together.

  4. Click Apply at the bottom of the page to save the changes. (Figure 7)



    Figure 7 - Bridge Settings

  5. To configure spanning tree for a specific port, click Port Settings and make the necessary changes. Click Apply at the bottom of the page to save the changes. (Figure 8)



    Figure 8
    - Port Settings

  6. When done, click Save Configuration to save the changes to NVRAM.



More information on the Spanning Tree Protocol.

Spanning-Tree Protocol (STP) was developed to prevent multiple open paths to the same switch (loops). There is an algorithm called STA (Spanning-Tree Algorithm) that is used to calculate a loop-free network topology.

Each port sends small packets addressed to itself and if it receives one back, it knows that there is a loop somewhere in the configuration and the switch will set that port to blocking mode. This process disables it for normal network traffic (Spanning Tree packets will still be allowed to pass).

When the Spanning Tree protocol is enabled the following parameters can be configured:

  • Hello Time - The interval between configuration messages sent by the spanning tree algorithm.
  • Max Age - The amount of time before a configuration message is discarded by the system.
  • Forward Delay - The amount of time the system spends in "learning" and "listening" states.
  • Bridge Priority - The priority setting amongst other switches in the spanning tree.

In some cases, it may be necessary to set certain ports to Fastlink, which disables Spanning Tree for that port only (as disabling Spanning Tree for the entire switch is generally not desirable). This is typically done to resolve timeout issues with DHCP clients that boot especially fast. Spanning Tree has a 30 second timeout period in which the port will be set to blocking mode until the algorithm can ascertain if there are loops. When a DHCP client boots up while the port is still in blocking mode, it can prevent it from obtaining an IP address.



 


Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips.

문서 ID: SLN116134

최종 수정일: 10/30/2012 12:00 AM


이 문서 평가하기

정확함
유용함
이해하기 쉬운
이 문서가 도움이 되셨나요?
지원 미지원
피드백을 보내 주십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.
죄송합니다. 현재 피드백 시스템은 사용하실 수 없습니다. 잠시 후에 다시 시도하십시오.

피드백을 보내주셔서 감사합니다.