3110cn / 3115cn / 3130cn - Paper Jam Error 077-907
3110cn / 3115cn / 3130cn - Paper Jam Error 077-907
3110cn 3115cn 3130cn Paper Jam Error 077-907
Open and close the front cover.
Open the front cover (Figure 1).
Figure 1: Opening the Front Cover
Close the front cover (Figure 2).
Figure 2: Closing the Front Cover
Reseat the fuser.
Turn off the printer and wait for 30 minutes.
Push the side button and open the front cover. (Figure 1)
Figure 1: Opening the Front Cover
Lift the duplex gate to its upright position. (Figure 2)
Figure 2: Lifting the Duplex Gate
Release the levers at both ends of the fuser. (Figure 3)
Figure 3: Releasing the Levers
Hold both sides of the installed fuser, and then pull inward lightly and then upward. (Figure 4)
Figure 4: Removing the Fuser
With the connector of the fuser toward the slot, push the connector into the slot firmly. (Figure 5)
Make sure that the fuser is firmly fixed in the slot and cannot be moved easily.
Figure 5: Inserting the Fuser
Lock both levers at the ends of the fuser. (Figure 6)
Figure 6: Locking the Levers
Lower the paper-transfer chute to its horizontal position. (Figure 7)
Figure 7: Lowering the Paper-Transfer Chute
Close the front cover. (Figure 8)
Figure 8: Closing the Front Cover
Reseat the duplexer.
Remove any print jobs from the center output tray and close the multipurpose feeder cover before opening the front cover.
Make sure the printer is powered off.
Push the side button and open the front cover (Figure 1).
Figure 1: Opening the Front Cover
Hold the handles of the transfer belt as shown (Figure 2) and open the unit fully.
Caution:
Do not touch the inside of the printer. Some parts may be hot. Allow time for the printer to cool before attempting to remove parts in this area.
Figure 2: Removing the Transfer Belt
Hold both sides of the transfer belt with both hands and pull up the right side of the unit until the peg on the right side comes out of the groove (Figure 3).
Figure 3: Removing the Peg from the Groove
Shift the transfer belt to the right and remove the unit from the printer.
Release the lock by pulling the lever of the duplex module, and then raise the module (Figure 4).
Figure 4: Removing the Duplexer
Release the two tabs on the back side of the duplex module from the holes on the front cover, then remove the duplex module.
Check that the cap covering the duplexer connection has been removed (Figures 5 and 6).
Figure 5: Front View, Duplexer Cap on Connector
Figure 6: Side View, Duplexer Cap on Connector
Check that the duplexer connection is attached to the receiving end of the printer (Figures 7 and 8).
Figure 7: Front View, Correct Duplexer Cap Connection
Figure 8: Side View, Incorrect Duplexer Cap Connection
Perform steps 3-10 in reverse order to reassemble the printer.
Inspect the duplex gate for damage.
Turn off the printer and wait for 30 minutes. Push the side button and open the front cover (Figure 1). Figure 1: Opening the Front Cover
Lift the duplex gate to its upright position (Figure 2). The duplex gate should freely pivot vertically with no lateral (side-to-side) motion. Ensure that neither one of the pivot pins (located on either side of the duplex gate) are broken. Figure 2: Lifting the Duplex Gate
If the duplex gate is damaged, replace it.
Inspect the exit chute for damage.
Open the front cover (Figure 1).
Figure 1: Opening the Front Cover
With the top cover open, visually inspect the exit chute for damage (Figure 2). There should be no burrs, and the rollers should rotate freely.
Figure 2: Exit Chute
Note:
There is no need to unscrew the exit chute from the front cover. The image shows the exit chute detached from the front cover in order to more easily distinguish it from the background.
Close the front cover (Figure 3).
Figure 3: Closing the Front Cover
If the exit chute is damaged, replace the front cover.
Run diagnostics on the duplexer jam sensor.
Make sure the printer is powered off.
Push the side button and open the front cover (Figure 1)
Figure 1: Opening the Front Cover
Hold the handles of the belt unit / transfer belt as shown (Figure 2) and open the unit fully.
Caution:
Do not touch the inside of the printer. Some parts may be hot. Allow time for the printer to cool before attempting to remove parts in this area.
Figure 2: Removing the Transfer Belt
Hold both sides of the belt unit / transfer belt with both hands and pull up the right side of the unit until the peg on the right side comes out of the groove (Figure 3).
Figure 3: Removing the Peg from the Groove
Shift the belt unit / transfer belt to the right and remove the unit from the printer.
Hold down the and buttons on the printer and power the printer on.
Release your fingers from the keys when the message Diagnosing... appears, which then displays Customer Mode and ESS Diag.
Press the button until IOT Diag appears and press the button.
When Digital Input appears on the LCD, press the button until Digital Input appears, and then press the button.
Press the or button until DI-1 appears, and then press the button twice.
Toggle the actuator on the duplexer, which causes the counter on the Operator Panel to increase by 1. If the counter does not increase by 1, replace the duplexer.
Press the Cancel button to stop this test.
Power the printer off.
Perform steps 3 through 5 in reverse to reinstall the belt unit / transfer belt, and then power on the printer.
Run diagnostics on the duplexer clutch.
Power off the printer.
Close all printer covers and doors.
Hold down the and buttons on the printer and power the printer on.
Release your fingers from the keys when the message Diagnosing... appears. Customer Mode and ESS Diag are displayed.
Press the button to select ESS Diag.
Press the button until IOT Diag appears and press the button.
On the LCD, Digital Input appears.
Press the button until Digital Output appears and press the button.
Press the button until DO-35 READY appears and press the button.
On the LCD, DO-35 EXEC appears and the motor noise is heard.
Press the Cancel button to stop the test.
On the LCD, DO-35 READY appears.
Press the Menu button.
Power the printer off and then back on.
If the diagnostic fails, Please contact Dell Technical Support for further advice.
Run diagnostics on the duplexer motor.
Power off the printer.
Close all printer covers and doors.
Hold down the and buttons on the printer and power the printer on.
Release your fingers from the keys when the message Diagnosing... appears. Customer Mode and ESS Diag are displayed.
Press the button to select ESS Diag.
Press the button until IOT Diag appears and press the button.
On the LCD, Digital Input appears.
Press the button until Digital Output appears and press the button.
Press the button until DO-13 READY appears and press the button.
On the LCD, DO-13 EXEC appears and the motor noise should be heard.
Press the Cancel button to stop the test.
On the LCD, DO-13 READY appears.
Press the Menu button.
Power the printer off and then back on.
If the diagnostic fails, Please contact Dell Technical Support for further advice.
Run diagnostics on the multi-purpose feeder (MPF) turn clutch.
Power off the printer.
Close all printer covers and doors.
Remove the 250-sheet tray. (Figure 1)
Figure 1 - Removing the 250-Sheet Tray
Hold down the and buttons on the printer and power the printer on.
Release your fingers from the keys when the message Diagnosing... appears. Customer Mode and ESS Diag are displayed.
Press the button to select ESS Diag.
Press the button until IOT Diag appears and press the button.
On the LCD, Digital Input appears.
Press the button until Digital Output appears and press the button.
Press the button until DO-a READY appears and press the button.
On the LCD, DO-a EXEC appears and the motor noise should be heard without a grinding noise.
Press the button until DO-2b READY appears and press the button.
On the LCD, DO-2b EXEC appears and the rollers spin.
Press the Cancel button to stop the test.
On the LCD, DO-2b READY appears.
Press the Menu button.
Power the printer off.
Replace the 250-sheet tray and then power the printer back on.
If the MPF does not function properly, Please contact Dell Technical Support for further advice.
Run diagnostics on the feed drive motor.
Power off the printer.
Close all printer covers and doors.
Hold down the and buttons on the printer and power the printer on.
Release your fingers from the keys when the message Diagnosing... appears. Customer Mode and ESS Diag are displayed.
Press the button to select ESS Diag.
Press the button until IOT Diag appears and press the button.
On the LCD, Digital Input appears.
Press the button until Digital Output appears and press the button.
Press the button until DO-a READY appears and press the button.
On the LCD, DO-a EXEC appears and the motor noise should be heard.
Press the Cancel button to stop the test.
On the LCD, DO-a READY appears.
Press the Menu button.
Power the printer off and then back on.
If the diagnostic fails, Please contact Dell Technical Support for further advice.
If the diagnostic passes, Please contact Dell Technical Support for further advice
Article ID: SLN162413
Last Date Modified: 08/08/2016 08:40 AM
Rate this article
Accurate
Useful
Easy to understand
Was this article helpful?
Yes No
Send us feedback
Comments cannot contain these special characters: <>()\
Sorry, our feedback system is currently down. Please try again later.
Thank you for your feedback.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\