How to Ensure Optimal USB Device Performance - Technical Assistance Bulletin (TAB) - 180399

How to Ensure Optimal USB Device Performance - Technical Assistance Bulletin (TAB) - 180399




Best Practices For USB Device Users

This document explains several best practices to ensure USB (Universal Serial Bus) devices work optimally:

  • If a system is booted from a USB device (such as a memory key, USB floppy drive, USB HDD, optical USB drive, etc), the device should be connected to a root port in the system back panel of the system (instead of a USB hub). Connecting a USB bootable device in a USB hub will increase the detection time and power on time of the device and may cause the boot process to timeout.

  • The USB root port detection order in desktop systems during the boot process is as follows:


    1. Back panel 4-stack USB ports (bottom to top).
    2. System front panel two ports.
    3. Back 2-stack USB ports.

  • When connecting a USB device to the system that has a legacy ATAPI/EIDE device that serves the same function as another device in the system (such as a USB optical drive and ATAPI/EIDE optical drive), the system BIOS will treat the legacy ATAPI/EIDE device as the higher priority device and detect/enumerate it first. If such a situation arises, the legacy device should be disabled first in the system BIOS.

  • When booting to a DOS environment, it is recommended to have only the USB boot device, keyboard and mouse connected to the system root ports. Do not connect the keyboard or mouse to separate USB hubs, especially to separate USB 2.0 specification hubs or the front USB connectors in the system. Keyboards and mice are typically USB 1.0/1.1 devices and work on slower speeds. Detecting keyboards and mice in these hubs will take longer and might lead to systems locking during the boot process.

  • Not all USB devices have drivers native for the Microsoft® Windows® XP or Windows 2000 operating systems. Users will need to install vendor-specific drivers for optimal functionality. Always check for driver availability to any other operating system. When installing a USB device that does not have drivers native to Windows, carefully follow the device manufacturer's instructions. In particular, pay special attention if the drivers must be installed before plugging the device into the USB port for the first time.

  • Some USB devices and protocols have not been validated by Dell. The most common protocols validated for use on Dell systems are SCSI and ATAPI in USB.

  • When a USB memory key is attached to a system without a floppy drive, Norton Antivirus (or any other antivirus program) may confuse the memory key as a floppy drive and not allow the system to shutdown properly. Remove the USB key before shutting down the system.

  • USB hubs in all Dell flat panel monitors follow the USB 2.0 specification.

  • When a non-bootable USB 2.0 device is attached to the system at same time as a bootable USB 1.1 device, the system will find the USB 2.0 device faster and will fail to boot. Either opt to use the USB 2.0 as the boot device, or remove all the non-bootable USB 2.0 devices before booting with the USB 1.1 device connected.

USB VersionLogoRelease Information
USB 1.0
  • The original release of USB
  • Transferring 12 Mbps
USB 1.1
  • Also known as “full-speed USB”
  • Minor modifications for the hardware and the specifications.
  • This version of USB still only supports a rate of 12 Mbps.
USB 2.0
  • “Hi-speed USB”
  • Capable of supporting a transfer rate of up to 480 Mbps.
  • Backwards-compatible (can support USB 1.0 and 1.1 devices and cables)
Table 1: USB Version History



 
Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips.

Identifikátor článku: SLN30966

Dátum poslednej zmeny: 06/17/2009 12:00 AM


Ohodnotiť tento článok

Presné
Užitočné
Jednoducho pochopiteľné
Bol pre vás tento článok užitočný?
Áno Nie
Pošlite nám pripomienky.
Poznámky nemôžu obsahovať nasledujúce špeciálne znaky: <>()\
Ľutujeme, náš systém odosielania pripomienok je momentálne nefunkčný. Skúste znova neskôr.

Ďakujeme vám za pripomienky.