What is the C-State ?

What is the C-State ?


In order to save energy when the CPU is idle, the CPU can be commanded to enter a low-power mode. Each CPU has several power modes and they are collectively called "C-states" or "C-modes". In this article we will explain what these modes are, what they do and the modes supported by each processor.

The lower-power mode was first introduced with the 486DX4 processor, so this concept is far from new. With time, however, more power modes were introduced and enhancements were made to each mode so the CPU could consume less power when it is in one of these low-power modes.

The basic idea of these modes is to cut the clock signal and power from idle units inside the CPU. The more units you stop (by cutting the clock), reduce the voltage or even completely shut down, the more energy you save, but more time is required for the CPU to "wake up" and again be 100% operational.

These modes are known as "C-states". They are numbered starting at C0, which is the normal CPU operating mode, i.e. the CPU is 100% turned on. The higher the C number is, the deeper is the CPU sleep mode, i.e. more circuits and signals are turned off and the more time the CPU will take to go back to C0 mode, i.e. to wake-up.

Each mode is also known by a name and several of them have sub-modes with different power saving levels – and thus wake-up time.

In the table below we summarize all C-state modes currently available. Modes C1 to C3 work by basically cutting clock signals used inside the CPU, while modes C4 to C6 work by reducing the CPU voltage. "Enhanced" modes can do both at the same time.

Mode

Name

What it does

CPUs

C0

Operating State

CPU fully turned on

All CPUs

C1

Halt

Stops CPU main internal clocks via software; bus interface unit and APIC are kept running at full speed.

486DX4 and above

C1E

Enhanced Halt

Stops CPU main internal clocks via software and reduces CPU voltage; bus interface unit and APIC are kept running at full speed.

All socket 775 CPUs

C1E

Stops all CPU internal clocks.

Turion 64, 65-nm Athlon X2 and Phenom CPUs

C2

Stop Grant

Stops CPU main internal clocks via hardware; bus interface unit and APIC are kept running at full speed.

486DX4 and above

C2

Stop Clock

Stops CPU internal and external clocks via hardware

Only 486DX4, Pentium, Pentium MMX, K5, K6, K6-2, K6-III

C2E

Extended Stop Grant

Stops CPU main internal clocks via hardware and reduces CPU voltage; bus interface unit and APIC are kept running at full speed.

Core 2 Duo and above (Intel only)

C3

Sleep

Stops all CPU internal clocks

Pentium II, Athlon and above, but not on Core 2 Duo E4000 and E6000

C3

Deep Sleep

Stops all CPU internal and external clocks

Pentium II and above, but not on Core 2 Duo E4000 and E6000; Turion 64

C3

AltVID

Stops all CPU internal clocks and reduces CPU voltage

AMD Turion 64

C4

Deeper Sleep

Reduces CPU voltage

Pentium M and above, but not on Core 2 Duo E4000 and E6000 series; AMD Turion 64

C4E/C5

Enhanced Deeper Sleep

Reduces CPU voltage even more and turns off the memory cache

Core Solo, Core Duo and 45-nm mobile Core 2 Duo only

C6

Deep Power Down

Reduces the CPU internal voltage to any value, including 0 V

45-nm mobile Core 2 Duo only




Need more help?
Find additional PowerEdge and PowerVault articles
Watch Part Replacement Videos for Enterprise products

Visit and ask for support in our Communities

Create an online support Request



Article ID: QNA41893

Last Date Modified: 09/14/2019 02:33 AM


Rate this article

Accurate
Useful
Easy to understand
Was this article helpful?
Yes No
Send us feedback
Comments cannot contain these special characters: <>()\
Sorry, our feedback system is currently down. Please try again later.

Thank you for your feedback.