Dell PowerEdge - How to configure the iDRAC 9 and the LifeCycle Controller Network IP

Dell PowerEdge - How to configure the iDRAC 9 and the LifeCycle Controller Network IP


Article summary: This article explains how to configure the IP address of the remote management card, the DRAC and then connect to the web interface. The second part of this article explains how to configure the network settngs of the LifeCycle Controller when launched for the same time.

Note: This article is part of the PowerEdge 14G startup page available here.


Table of content
  1. Configure the iDRAC 9
  2. Configure the LifeCycle Controller (LCC)
  3. iDRAC Protocol Ports

Configure the iDRAC 9

The Integrated Dell Remote Access Controller (iDRAC) is designed to make system administrators more productive and improve the overall availability of Dell systems. iDRAC alerts administrators to system issues, help them perform remote system management and reduces the need for physical access to the system.

1. Options to set up the iDRAC IP address

You must configure the initial network settings based on your network infrastructure to enable the communication to and from iDRAC. You can set up the IP address using one of the following interfaces:

Note: In the case of blade servers, you can configure the network setting using the Chassis LCD panel only during initial configuration of CMC. After the chassis is deployed, you cannot reconfigure iDRAC using the Chassis LCD panel.


2. Setting up the iDRAC IP using "iDRAC Setting Utility" (F2 during startup)

You can set up the IP address or use the default iDRAC IP address 192.168.0.120 to configure initial network settings, including setting up DHCP or the static IP for iDRAC. By default, the dedicated iDRAC network card is disabled. The iDRAC is sharing the network card on LOM 1 (LAN on Motherboard). In the case of blade servers, the iDRAC network interface is disabled by default.

Example setting up iDRAC IP using iDRAC settings utility (F2 during startup):

  1. Turn on the managed system.
  2. Press <F2> during Power-on Self-test (POST).



  3. In the System Setup Main Menu page, click iDRAC Settings. The iDRAC Settings page is displayed.



  4. Click Network. The Network page is displayed.



  5. Specify the network settings. Under Enable NIC, select Enabled.
    - Shared LOM (1, 2, 3 or 4) will share one of the NIC on the motherboard
    - Dedicated NIC will use the dedicated network interface




  6. Set the IPv4 or IPv6 network settings, depending on the local configuration



  7. Click Back, click Finish, and then click Yes. The network information is saved and the system reboots





iDRAC configuration is now completed. The iDRAC Web User Interface can now be reached with any supported browser (IE, Firefox, Chrome, Safari). In that case the iDRAC will respond on the IP "192.168.0.120".
If there is any access issue:

  • Try to ping the iDRAC IP to check that the network configuration has been replied.
  • Check which LOM (network card) has been selected in the iDRAC network settings. The LOM can be shared with the server network cards or use the dedicated iDRAC NIC's.
Important: After you configure iDRAC IP address, ensure that you change the default user name and password after setting up the iDRAC IP address.

Once the iDRAC IP is configured you can access to the interface with a supported browser. Which username and password use is explained in the article What is the default password for iDRAC?

Note: In the iDRAC settings, it is possible to enable directory log in (Microsoft AD or LDAP).

For more information about logging in to the iDRAC and iDRAC licenses, see the latest Integrated Dell Remote Access Controller User's Guide at Dell.com/idracmanuals.


When connecting to the iDRAC interface, the following message will be displayed "There is a problem with this website's security certificate". This is normal as the SSL certificate from the iDRAC is self-signed and is not confirmed by an external provider. To connect, click on "Continue to this website".




2. Configure the LifeCycle Controller (LCC)

Dell Lifecycle Controller is an advanced embedded systems management technology that enables remote server management using integrated Dell Remote Access Controller (iDRAC). Using Lifecycle Controller, you can update the firmware using a local or Dell-based firmware repository. The OS Deployment wizard available in Lifecycle Controller enables you to deploy an operating system.

To access the LCC, please press F10 during startup. The lifecycle controller shares an IP address with one of the server network cards. The IP address has to be configured at least once to use the update and the OS installation feature.

To set up your PowerEdge server using Lifecycle Controller:
1. Connect the video cable to the video port and the network cables to the iDRAC and LOM port.

Figure 1. Video port, iDRAC dedicated port, and LAN On Motherboard (LOM) port




Turn on or restart the server and press F10 to start Lifecycle Controller.



Figure 2: Starting Lifecycle Controller

Note: you miss pressing F10, press and hold the power button for three seconds to restart the server.

Note: The Initial Setup Wizard is displayed only when you start Lifecycle Controller for the first time.

Select the language and keyboard type and click Next.


Figure 3: Language and Keyboard Selection page


Read the product overview and click Next.


Figure 4. Product Overview page


Configure the network settings, wait for the settings to be applied, and click Next.


Figure 5. Lifecycle Controller Network Settings page


Configure the iDRAC network settings, wait for the settings to be applied, and click Next.


Figure 6. iDRAC Network and Credential Configuration page


Verify the applied network settings and click Finish to exit the Initial Setup Wizard.


Figure 7. Summary page

Note: The Initial Setup Wizard is displayed only when you start Lifecycle Controller for the first time. If you want to make configuration changes later, restart the server, press F10 to start Lifecycle Controller, and select Settings or System Setup from the Lifecycle Controller home page.

Click Firmware Update > Launch Firmware Update and follow the instructions on the screen to update the firmware.


Figure 8. Firmware Update page


Click OS Deployment > Deploy OS and follow the instructions on the screen to deploy the operating system.


Figure 9. OS Deployment page


The next steps to install an operating system are provided in the article How to install the Operating System on a server.


iDRAC Protocol Ports

iDRAC listens for Connections

Port Number

Type

Protocol

Configurable

Max Encryption Level

22

TCP

SSH

Yes

256-bit SSL

23

TCP

Telnet

Yes

None

80

TCP

HTTP

Yes

None

161

UDP

SNMP agent

Yes

None

443

TCP

HTTPs

Yes

256-bit SSL

623

UDP

RMCP/RMCP+

No

128-bit SSL

5900

TCP

vConsole/vMedia

Yes

128-bit SSL

5901

TCP

VNC

No

128-bit SSL

iDRAC uses as a client

25

TCP

SMTP

Yes

None

53

UDP

DNS

No

None

68

UDP

DHCP

No

None

69

TFTP

TFTP

No

None

123

UDP

NTP

No

None

162

UDP

SNMP traps

Yes

None

445

TCP

CIFS

No

None

636

TCP

LDAPS (LDAP SSL)

No

256-bit SSL

2049

TCP

NFS

No

None

3269

TCP

LDAPS GC (Global Catalog)

No

256-bit SSL




Need more help?
Find additional PowerEdge and PowerVault articles
Watch Part Replacement Videos for Enterprise products

Visit and ask for support in our Communities

Create an online support Request



Article ID: SLN306877

Last Date Modified: 07/17/2019 05:05 AM


Rate this article

Accurate
Useful
Easy to understand
Was this article helpful?
Yes No
Send us feedback
Comments cannot contain these special characters: <>()\
Sorry, our feedback system is currently down. Please try again later.

Thank you for your feedback.