Dell TPM 1.2 Firmware Update Utility

This utility updates the system TPM 1.2 firmware to the new revision. If the utility is run on a system with TPM 2.0, it can switch the TPM mode to TPM 1.2. Switching the TPM mode may have operating system implications.

Note 1: You must provide a bootable DOS USB drive. This executable file does not create the DOS system files.
Note 2 : Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 3: The TPM must be ON and Enabled in BIOS Setup, and the TPM must not be owned. If the TPM is owned, go to BIOS Setup and clear the TPM before proceeding. You may need to run TPM.msc to reinitiate the TPM under Windows operating system.
Note 4: When the TPM ownership is cleared, some operating system will automatically take ownership of the TPM on the next boot (TPM AutoProvisioning). This feature needs to be disabled in the operating system to proceed with the update.

Dell TPM Update Utility for Windows/DOS

Download
1. Click Download File, to download the file.
2. When the File Download window is displayed, click Save to save the file to your hard drive.

Clear the TPM (See Notes 2, 3 and 4)
1. Before running the TPM update utility, clear the TPM Owner.

Disable TPM Auto Provisioning in Windows (See Note 4)
1. Boot to Windows
2. Launch the PowerShell Command window in Administrator mode
3. At the Powershell command prompt, start the command:
> Disable-TpmAutoProvisioning
4. Confirm the following results:
- AutoProvisioning: Disabled
5. Reboot the system, to BIOS Setup by pressing F2.
6. Navigate to Security > TPM 1.2/2.0 Security.
7. Click the Clear checkbox and select Yes at the prompt to clear the TPM settings. (You can skip it if the item is grayed out)
8. Click Exit to save changes.
9. Reboot system to Windows.
10. Confirm the TPM is not owned. The TPM should no longer be automatically provisioned by Windows.
11. When the TPM update is finished, launch the PowerShell command in Administrator mode to re-enable the auto provisioning.
> Enable-TpmAutoProvisioning
12. Confirm the following results:
- AutoProvisioning: Enabled

Updating the TPM update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System auto restarts and updates the TPM during the system startup.
3. When the TPM update is finished, the system auto reboots to take effect.

Updating the TPM update utility from DOS environment, with Legacy Boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then Press F12 key and Select USB Storage Device and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable file is located.
4. DOS system auto restarts and updates the TPM during the system startup.
5. When the TPM update is finished, the system auto reboots to take effect.

Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
3. Change UEFI to Legacy of Boot List Option.
4. Click Apply, click Exit to save changes and reboot system.
5. Press F12, then Select USB Storage Device and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable file is located.
7. When the TPM update is finished, the system auto reboots to take effect.
8. Go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Click Apply, click Exit to save changes and reboot system.