SK Hynix SC300 M.2 Solid State Drive Firmware Update
Újraindítás szükséges Telepítve Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
This package provides the firmware for SK Hynix SC300 M.2 2280 128GB/256GB/512GB, Revision 20101P00, and is supported on Inspiron, Latitude, OptiPlex, Precision and XPS models running the following Windows operating systems: Windows 7, Windows 8, Windows 8.1 and Windows 10.
Ajánlott
Kompatibilitás ellenőrzése
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót. Mutasd meg, hogyan!
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet. A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
Fixes:
- Fixes an issue which can cause the SSD to occasionally not wake up from low power mode
Enhancement:
- Not Applicable
További információ- Fixes an issue which can cause the SSD to occasionally not wake up from low power mode
Enhancement:
- Not Applicable
Verziószám
20101P00, A00
Kibocsátás dátuma
18 jan. 2017
Letöltés típusa
Firmware
Kategória
Adattárolás
Fontosság
OptionalDell Technologies recommends reviewing this update to determine if it applies to your system. The update contains changes that impact only certain configurations or provides new features that may or may not apply to your environment.
Elérhető formátumok View Important Information
Fájlformátum: ZipPack External
Fájlnév: SK Hynix SC300 M.2 Solid State Drive Firmware Update_ZPE.exe
Fájlméret: 15.31 MB
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, and then run (double-click) it to unzip the set of files. Follow the instructions to complete the installation.
A letöltés integritásának biztosítása érdekében ellenőrizze az ellenőrző összeg értékét.
MD5:
00bd54fd909e39143fd7f29b64a1afca
SHA1:
8b85aa16a9ffe3ce73fe95cd26fb8510c213065c
SHA-256:
e3e18a656789af1bf83aa02969ea8d4e8ae3fc331f3e69f829f298ccaecbcc24
A letöltéssel Ön elfogadja a Dell szoftverlicenc-szerződés feltételeit.
Fontos tudnivalók
- There is the User Account Control warning message popup when launching the tool since this tool runs as administrator. Then, please press Yes to run this tool.
- This tool supports only internal SATA cable connection.
- For important data, it is recommended to save data or keep it backup before updating the firmware.
- Please DO NOT power off or disconnect the solid state drive from host during firmware update is in progress. It could make the drive does not work.
- This tool supports only internal SATA cable connection.
- For important data, it is recommended to save data or keep it backup before updating the firmware.
- Please DO NOT power off or disconnect the solid state drive from host during firmware update is in progress. It could make the drive does not work.
Támogatott operációs rendszerek
Windows 7 (32 bites)
Windows 7, 64-bit
Windows 8 (32 bites)
Windows 8, 64-bit
Windows 8.1 (32 bites)
Windows 8.1 (64 bites)
Windows 10 (32 bites)
Windows 10, 64-bit
A következőre vonatkozik:
HYNIX SC300 128G M.2 2280 SATA SSD (CLASS 20)
HYNIX SC300 256G M.2 2280 SATA SSD (CLASS 20)
HYNIX SC300 512G M.2 2280 SATA SSD (CLASS 20)
Telepítési utasítások
Download
1. Click Download File and follow the remaining prompts to download the file.
2. When the File Download window appears, click Run to unzip the download package into your hard drive.
3. The file explorer will open pointing to the directory containing the download package. Please take note of the path.
------------------------------------------------------------------------------------------
ATTENTION
1. Backup the SSD.
2. Switch to AC Power
------------------------------------------------------------------------------------------
Firmware upgrade through the Windows utility
Procedure
1. Go to the directory containing the download package as noted above.
2. Run the firmware update utility with administrator privilege (right-click on the executable, then select "Run as administrator").
3. Follow the on-screen instructions.
4. Check if status is "Ready" in [Update] column.
5. Select a drive(s) in list. The [FW Update] button will be enabled when selected drive is SK Hynix SSD.
6. Click [FW Update].
7. If the update is successful, it displayed in green, otherwise displayed in red.
8. After finishing the update successfully, the tool will ask to reboot the system. If you want to reboot the system, click [OK] button otherwise click [Cancel] button if you want to do later.
------------------------------------------------------------------------------------------
Firmware upgrade using the bootable image
1. An ISO image is provided in the download package. Use that image to create a bootable USB thumb drive. You may want to consider using UNetBootin.
2. Boot the system from the USB thumb drive created in Step 1.
3.Your PC will boot up with Linux booting screen and it displays SSDs that connected to your PC.
4. The FW update tool will seek SK Hynix SC300 SSD. If the tool find a SK Hynix SC300, it will start to update automatically, if not it displays an error message.
5. After successful FW update, PC will shutdown after about 10 sec.
1. Prepare a USB thumb drive
(1) USB storage and ISO image Writer(like UNetBootin) are needed for updating SSD FW with this package.
(2) Run unetbootin-windows-608.exe
(3) Check 'DiskImage' button and select path to ISO file using the ' ... ' option button.
(4) If USB Drive is ready, then UNetbooin will show the driver letter.
(5) Select OK to copy ISO bootable image to USB thumb drive
(6) Once installation is completed, please follow the next steps on UNetbootin Window.
*.Installation Instructions:
For the detail usage of this package, Please refer to the attached Update Tool Manual.
1. Click Download File and follow the remaining prompts to download the file.
2. When the File Download window appears, click Run to unzip the download package into your hard drive.
3. The file explorer will open pointing to the directory containing the download package. Please take note of the path.
------------------------------------------------------------------------------------------
ATTENTION
1. Backup the SSD.
2. Switch to AC Power
------------------------------------------------------------------------------------------
Firmware upgrade through the Windows utility
Procedure
1. Go to the directory containing the download package as noted above.
2. Run the firmware update utility with administrator privilege (right-click on the executable, then select "Run as administrator").
3. Follow the on-screen instructions.
4. Check if status is "Ready" in [Update] column.
5. Select a drive(s) in list. The [FW Update] button will be enabled when selected drive is SK Hynix SSD.
6. Click [FW Update].
7. If the update is successful, it displayed in green, otherwise displayed in red.
8. After finishing the update successfully, the tool will ask to reboot the system. If you want to reboot the system, click [OK] button otherwise click [Cancel] button if you want to do later.
------------------------------------------------------------------------------------------
Firmware upgrade using the bootable image
1. An ISO image is provided in the download package. Use that image to create a bootable USB thumb drive. You may want to consider using UNetBootin.
2. Boot the system from the USB thumb drive created in Step 1.
3.Your PC will boot up with Linux booting screen and it displays SSDs that connected to your PC.
4. The FW update tool will seek SK Hynix SC300 SSD. If the tool find a SK Hynix SC300, it will start to update automatically, if not it displays an error message.
5. After successful FW update, PC will shutdown after about 10 sec.
1. Prepare a USB thumb drive
(1) USB storage and ISO image Writer(like UNetBootin) are needed for updating SSD FW with this package.
(2) Run unetbootin-windows-608.exe
(3) Check 'DiskImage' button and select path to ISO file using the ' ... ' option button.
(4) If USB Drive is ready, then UNetbooin will show the driver letter.
(5) Select OK to copy ISO bootable image to USB thumb drive
(6) Once installation is completed, please follow the next steps on UNetbootin Window.
*.Installation Instructions:
For the detail usage of this package, Please refer to the attached Update Tool Manual.
Illesztőprogramokkal kapcsolatos súgó és oktatóanyagok
További letöltésekért lépjen a következő oldalra: Illesztőprogramok és letöltések. Az ezen az oldalon található információk használatával kapcsolatban látogasson el az illesztőprogramokkal kapcsolatos súgó és oktatóanyagok oldalára.