LSI Logic PERC 4/Di, v.4.17.2, A01

Dell PowerEdge RAID Controller 4/Di Device Driver for Windows NT
4.0

Ottieni il driver più recente

Inserisci i dettagli del prodotto per visualizzare le ultime informazioni sui driver per il sistema.

Questo driver non è compatibile

Questo driver è aggiornato

Le informazioni sui driver sono aggiornate. Per visualizzare tutti i driver per il PowerEdge 2600, accedi a Driver e download.

Correzioni e miglioramenti

Changes from 4.15
=================

1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.

2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.

3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.

4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.

Versione

Versione 4.17.2, A01

Categoria

RAID SCSI

Data di rilascio

07 nov 2002

Ultimo aggiornamento

03 nov 2011

Importanza

Formati disponibili

Formato file: Hard-Drive
Nome file: Perc4di_NT4.17.2.exe
Tipo di download: HTTP
Dimensioni file: 49.82 KB
Descrizione del formato:
Questo formato di file è costituito da un archivio di file che possono essere decompressi in una directory sul disco rigido. L'installazione può essere quindi eseguita da tale directory.
To ensure the integrity of your download, please verify the checksum value.
MD5:
Non disponibile
SHA1:
Non disponibile
SHA-256:
Non disponibile

Con il download l'utente accetta i termini del Contratto di licenza del software Dell. (in Inglese)

Default Instructions for Perc4di_NT4.17.2.exe:

This program creates a Windows NT 4.0 driver diskette for
the controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.

1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.

Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.

Performing a New Installation of Windows NT 4.0
-----------------------------------------------

"Making PERC/CERC the Primary Controller in Windows NT 4.0"

1) Boot the system using the Windows NT 4.0 CD. As the
message

"Setup is inspecting your computer's hardware configuration."

appears. Press F6 immediately.

2) Within a few seconds, the Windows NT Setup screen
appears, requesting additional adapters in the system.
Press 'S' to specify an additional device, then press
Enter on the OTHER option in the selection screen.

3) Insert the PERC/CERC driver diskette created above and
press Enter.

"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"

appears. Press Enter to load the driver.

4) Press 'S' to load additional mass storage device driver
if required. Otherwise, press Enter to continue
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.

"Making PERC/CERC a Secondary Controller in Windows NT 4.0"

1) Start the Windows NT 4.0 installation process. Load the
device for the primary controller if necessary.

2) Windows NT Server Setup screen is displayed after loading
Windows NT Kernel. Press Enter to continue.

3) Setup displays mass storage devices that it has
recognized in your computer. Press 'S' to specify an
additional device, then press Enter on the OTHER option
in the selection screen.

4) Insert the PERC/CERC driver diskette created above and
press Enter.

"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"

appears. Press Enter to load the driver.

5) Press 'S' to load additional mass storage device drivers
if required; otherwise, press Enter to continue the
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.

Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server
-------------------------------------------------------------

If your server is already running Windows NT 4.0, then use
the following steps to add the PERC/CERC Windows NT 4.0
driver.

1) Insert the PERC/CERC driver diskette created above in
appropriate drive. The driver files can also be installed
from a local or network drive.

2) Click on Start > Control Panel > Settings. Double-click
on the Small Computer System Interface (SCSI) Adapter
icon.

3) Select the Drivers tab.

4) Click on the Add button.

5) Select Have Disk.

6) The Install From Disk box appears. Specify the location
of the PERC/CERC Windows NT 4.0 driver and click on OK.

7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.

This procedure will install the PERC/CERC drivers for
Windows NT v4.0. You must reboot the system after
installation has been completed successfully.

Tutorial e guida ai driver