LSI Logic PERC 4/Di, v.4.17.2, A01
AUTO-INSTALLATION Ce fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.Le contenu de cette page a peut-être été traduit automatiquement. Pour faire part de vos commentaires, remplissez le formulaire au bas de la page.
Dell PowerEdge RAID Controller 4/Di Device Driver for Windows NT
4.0
4.0
Recommandé
Trouver le meilleur téléchargement pour votre système
Saisissez les détails de votre produit pour afficher les dernières informations sur le pilote de votre système.Rechercher dans le support
Saisir votre modèle ou numéro de série Dell
Vous souhaitez rechercher votre produit ? Saisissez un identifiant de produit. Comment faire
Ce pilote n’est pas compatible
Ce pilote ne s’applique pas au produit sélectionné. Choisissez un autre produit pour saisir de nouveau les détails de votre produit pour ce pilote ou rendez-vous sur la page du support produit pour afficher tous les pilotes d’un autre produit.
Connectez-vous à Windows en tant qu’administrateur pour utiliser les fonctionnalités d’analyse automatique. Si vous êtes déjà connecté en tant qu’administrateur et que vous voyez ce message, redémarrez. Votre système est géré par votre administrateur IT et peut avoir des fonctionnalités limitées.
Trouver d’autres mises à jour. Utilisez SupportAssist pour trouver toutes les dernières mises à jour de pilotes disponibles pour votre appareil.
Correctifs et améliorations
Changes from 4.15
=================
1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.
4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.
En savoir plus=================
1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.
4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.
Version
4.17.2, A01
Date de publication :
07 nov. 2002
Type de téléchargement
Pilote
Catégorie
RAID SCSI
Importance
En optionDell Technologies recommande de consulter cette mise à jour pour déterminer si elle s’applique à votre système. La mise à jour comprend des modifications n’ayant d’impact que sur certaines configurations, ou propose de nouvelles fonctionnalités pouvant s’appliquer ou non à votre environnement.
Formats disponibles
Format de fichier : Extrait des fichiers directement vers le disque local
Nom du fichier : Perc4di_NT4.17.2.exe
Taille du fichier : 49.82 KB
Ce fichier est volumineux. En fonction de la vitesse de votre connexion, le téléchargement peut prendre un certain temps.
Description du format:
Ce format de fichier comprend une archive de fichiers qui peut être décompressée sur un répertoire du disque dur. L’installation peut être effectuée à partir de ce répertoire.
Afin de garantir l’intégrité de votre téléchargement, veuillez vérifier la valeur de la somme de contrôle.
MD5 :
Non disponible
SHA1 :
Non disponible
SHA-256 :
Non disponible
En effectuant le téléchargement, vous acceptez les conditions du Contrat de licence logicielle Dell. (en anglais)
Instructions d’installation
Default Instructions for Perc4di_NT4.17.2.exe:
This program creates a Windows NT 4.0 driver diskette for
the controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Performing a New Installation of Windows NT 4.0
-----------------------------------------------
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the
message
"Setup is inspecting your computer's hardware configuration."
appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen
appears, requesting additional adapters in the system.
Press 'S' to specify an additional device, then press
Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver
if required. Otherwise, press Enter to continue
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the
device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading
Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has
recognized in your computer. Press 'S' to specify an
additional device, then press Enter on the OTHER option
in the selection screen.
4) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers
if required; otherwise, press Enter to continue the
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server
-------------------------------------------------------------
If your server is already running Windows NT 4.0, then use
the following steps to add the PERC/CERC Windows NT 4.0
driver.
1) Insert the PERC/CERC driver diskette created above in
appropriate drive. The driver files can also be installed
from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click
on the Small Computer System Interface (SCSI) Adapter
icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the location
of the PERC/CERC Windows NT 4.0 driver and click on OK.
7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.
This procedure will install the PERC/CERC drivers for
Windows NT v4.0. You must reboot the system after
installation has been completed successfully.
This program creates a Windows NT 4.0 driver diskette for
the controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Performing a New Installation of Windows NT 4.0
-----------------------------------------------
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the
message
"Setup is inspecting your computer's hardware configuration."
appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen
appears, requesting additional adapters in the system.
Press 'S' to specify an additional device, then press
Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver
if required. Otherwise, press Enter to continue
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the
device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading
Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has
recognized in your computer. Press 'S' to specify an
additional device, then press Enter on the OTHER option
in the selection screen.
4) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers
if required; otherwise, press Enter to continue the
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server
-------------------------------------------------------------
If your server is already running Windows NT 4.0, then use
the following steps to add the PERC/CERC Windows NT 4.0
driver.
1) Insert the PERC/CERC driver diskette created above in
appropriate drive. The driver files can also be installed
from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click
on the Small Computer System Interface (SCSI) Adapter
icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the location
of the PERC/CERC Windows NT 4.0 driver and click on OK.
7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.
This procedure will install the PERC/CERC drivers for
Windows NT v4.0. You must reboot the system after
installation has been completed successfully.
Aide et didacticiels sur les pilotes
Pour plus de téléchargements, accédez à Pilotes et téléchargements. Pour obtenir de l’aide sur l’utilisation des informations affichées sur cette page, consultez la rubrique Aide et didacticiels pour les pilotes.