INSTALADO AUTOMÁTICAMENTEEste archivo se instaló automáticamente como parte de una actualización reciente. Si experimenta algún problema, puede descargarlo y reinstalarlo manualmente.
Es posible que el contenido de esta página se traduzca automáticamente. Para proporcionar comentarios, complete el formulario en la parte inferior de la página.
Este archivo se instaló automáticamente como parte de una actualización reciente. Si experimenta algún problema, puede descargarlo y reinstalarlo manualmente.
Dell PowerEdge RAID Controller 4/Di Device Driver for Windows NT 4.0
Recomendado
Encuentre la mejor descarga para su sistema
Ingrese los detalles del producto para ver la información más reciente del controlador para el sistema
Buscar soporte
Ingrese su modelo o etiqueta de servicio de Dell
¿Desea buscar su producto? Ingrese un identificador de producto.Mostrarme cómo
No se encontraron resultados. No pudimos encontrar ningún resultado para la búsqueda. Modifique la búsqueda e inténtelo de nuevo.
Este controlador no es compatible
Este controlador no se corresponde con el producto seleccionado. Elija otro producto para volver a ingresar los detalles del producto para este controlador o visite la página Soporte de productos para ver todos los controladores de un producto diferente.
Inicie sesión en Windows como administrador para utilizar el escaneo automático. Si ya inició sesión como administrador y ve este mensaje, reinicie el sistema.El administrador de TI administra el sistema y es posible que las funciones sean limitadas.
Encuentre más actualizaciones. Utilice SupportAssist para encontrar todas las actualizaciones de controladores más recientes para su dispositivo.
Correcciones y mejoras
Changes from 4.15 =================
1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.
4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.
Dell Technologies recomienda revisar esta actualización para determinar si corresponde a su sistema. La actualización contiene cambios que afectan solamente a ciertas configuraciones u ofrecen nuevas funciones que pueden aplicarse o no a su entorno.
Formato de archivo:Extrae archivos directamente al disco local
File Name:Perc4di_NT4.17.2.exe
Tamaño del archivo:49.82 KB
Este es un archivo grande. La descarga puede tardar, dependiendo de la velocidad de conexión.
Descripción del formato:
Este formato de archivo consiste en un archivo de archivos que se pueden descomprimir a un directorio en el disco duro. La instalación puede realizarse desde ese directorio.
This program creates a Windows NT 4.0 driver diskette for the controllers. You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
1) Download the file to a directory on your hard drive. The file downloaded is a self extracting executable. 2) Double click on the file to run the executable. 3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card. Configure the logical drives before proceeding with the driver install described below.
Performing a New Installation of Windows NT 4.0 -----------------------------------------------
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the message
"Setup is inspecting your computer's hardware configuration."
appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen appears, requesting additional adapters in the system. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver if required. Otherwise, press Enter to continue installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has recognized in your computer. Press 'S' to specify an additional device, then press Enter on the OTHER option in the selection screen.
4) Insert the PERC/CERC driver diskette created above and press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers if required; otherwise, press Enter to continue the installation process as usual. Windows NT 4.0 continues to be installed as usual. Please refer to the operating system installation documentation for further steps.
Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server -------------------------------------------------------------
If your server is already running Windows NT 4.0, then use the following steps to add the PERC/CERC Windows NT 4.0 driver.
1) Insert the PERC/CERC driver diskette created above in appropriate drive. The driver files can also be installed from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click on the Small Computer System Interface (SCSI) Adapter icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the location of the PERC/CERC Windows NT 4.0 driver and click on OK.
7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.
This procedure will install the PERC/CERC drivers for Windows NT v4.0. You must reboot the system after installation has been completed successfully.