LSI Logic PERC 4/Di, v.4.17.2, A01
AUTOMATISCH GEÏNSTALLEERD Dit bestand is automatisch geïnstalleerd als onderdeel van een recente update. Als u problemen ondervindt, kunt u deze handmatig downloaden en opnieuw installeren.De inhoud van deze pagina is mogelijk automatisch vertaald. Vul het formulier onderaan de pagina in om feedback te geven.
Dell PowerEdge RAID Controller 4/Di Device Driver for Windows NT
4.0
4.0
Aanbevolen
Vind de beste download voor uw systeem
Voer uw productgegevens in om de meest recente driverinformatie voor uw systeem weer te geven.Support zoeken
Voer uw Dell servicetag of model in
Wilt u uw product opzoeken? Voer een product-ID in. Meer informatie
Deze driver is niet compatibel
Deze driver is niet van toepassing op het geselecteerde product. Kies een ander product om uw productinformatie voor deze driver opnieuw in te voeren of ga naar de productsupportpagina om alle drivers voor een ander product weer te geven.
Meld u aan bij Windows als beheerder om automatische scanfuncties te gebruiken. Als u al bent aangemeld als beheerder en dit bericht ziet, start dan opnieuw op. Uw systeem wordt beheerd door uw IT-beheerder en de functies kunnen beperkt zijn.
Zoek meer updates. Gebruik SupportAssist om alle nieuwste driverupdates voor uw apparaat te vinden.
Probleemoplossingen en verbeteringen
Changes from 4.15
=================
1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.
4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.
Meer lezen=================
1) Driver is allocating enough continuous memory for the FLASH_WRITE_BLOCK(0x2c) command.
2) New commmand has been introduced to enhance the performance for SCSI I/O on non-raid SCSI channel.
3)In case of cluster reset, Driver was looping infinitely for the outstanding commands to get completed. This might result in the system hang. Driver has been modified to have a timeout and return Failure if the Firmware fails to complete the outstanding commands in a certain period of time.
4) Driver was allowing all the requests coming for a physical channel with TargetID greater than 15. Ideally Firmware should fail all the commands coming for the targetID > 15, but this fix has been put in the driver. Driver would return all the requests coming for the tagetID > 15 as an illegal requests.
Versie
4.17.2, A01
Releasedatum
07 nov. 2002
Downloadtype
Driver
Categorie
SCSI RAID
Belang
OptioneelDell Technologies raadt aan om deze update te bekijken om te bepalen of deze van toepassing is op uw systeem. De update bevat wijzigingen die alleen invloed hebben op sommige configuraties, of bevat nieuwe functies die al dan niet op uw omgeving van toepassing zijn.
Beschikbare bestandsindelingen
Bestandsindeling: Extraheert bestanden rechtstreeks naar de lokale harde schijf
Bestandsnaam: Perc4di_NT4.17.2.exe
Bestandsgrootte: 49.82 KB
Dit is een groot bestand. Afhankelijk van uw verbindingssnelheid kan het downloaden enige tijd duren.
Format-omschrijving:
Deze bestandsindeling bestaat uit een archief van bestanden die kunnen worden gedecomprimeerd in een map op de harde schijf. De installatie kan dan worden gedaan vanuit deze map.
Verifieer de checksum-waarde om de integriteit van uw download te garanderen.
MD5:
Niet beschikbaar
SHA1:
Niet beschikbaar
SHA-256:
Niet beschikbaar
Door te downloaden accepteert u de voorwaarden van de softwarelicentieovereenkomst van Dell. (in het Engels)
Ondersteunde besturingssystemen
Windows NT 4.0
Installatie-instructies
Default Instructions for Perc4di_NT4.17.2.exe:
This program creates a Windows NT 4.0 driver diskette for
the controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Performing a New Installation of Windows NT 4.0
-----------------------------------------------
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the
message
"Setup is inspecting your computer's hardware configuration."
appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen
appears, requesting additional adapters in the system.
Press 'S' to specify an additional device, then press
Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver
if required. Otherwise, press Enter to continue
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the
device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading
Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has
recognized in your computer. Press 'S' to specify an
additional device, then press Enter on the OTHER option
in the selection screen.
4) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers
if required; otherwise, press Enter to continue the
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server
-------------------------------------------------------------
If your server is already running Windows NT 4.0, then use
the following steps to add the PERC/CERC Windows NT 4.0
driver.
1) Insert the PERC/CERC driver diskette created above in
appropriate drive. The driver files can also be installed
from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click
on the Small Computer System Interface (SCSI) Adapter
icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the location
of the PERC/CERC Windows NT 4.0 driver and click on OK.
7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.
This procedure will install the PERC/CERC drivers for
Windows NT v4.0. You must reboot the system after
installation has been completed successfully.
This program creates a Windows NT 4.0 driver diskette for
the controllers. You will need a formatted 3 1/2 inch floppy
diskette for the following procedure.
1) Download the file to a directory on your hard drive. The
file downloaded is a self extracting executable.
2) Double click on the file to run the executable.
3) Click on the unzip button to extract files to the floppy.
Power down the system and install the PERC/CERC card.
Configure the logical drives before proceeding with the
driver install described below.
Performing a New Installation of Windows NT 4.0
-----------------------------------------------
"Making PERC/CERC the Primary Controller in Windows NT 4.0"
1) Boot the system using the Windows NT 4.0 CD. As the
message
"Setup is inspecting your computer's hardware configuration."
appears. Press F6 immediately.
2) Within a few seconds, the Windows NT Setup screen
appears, requesting additional adapters in the system.
Press 'S' to specify an additional device, then press
Enter on the OTHER option in the selection screen.
3) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
4) Press 'S' to load additional mass storage device driver
if required. Otherwise, press Enter to continue
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
"Making PERC/CERC a Secondary Controller in Windows NT 4.0"
1) Start the Windows NT 4.0 installation process. Load the
device for the primary controller if necessary.
2) Windows NT Server Setup screen is displayed after loading
Windows NT Kernel. Press Enter to continue.
3) Setup displays mass storage devices that it has
recognized in your computer. Press 'S' to specify an
additional device, then press Enter on the OTHER option
in the selection screen.
4) Insert the PERC/CERC driver diskette created above and
press Enter.
"CERC ATA100/4ch; PERC 4/Di-SC-DC; 3/DC-DCL-QC-SC Windows NT Driver"
appears. Press Enter to load the driver.
5) Press 'S' to load additional mass storage device drivers
if required; otherwise, press Enter to continue the
installation process as usual. Windows NT 4.0 continues
to be installed as usual. Please refer to the operating
system installation documentation for further steps.
Adding the PERC 3 Driver to an Existing Windows NT 4.0 Server
-------------------------------------------------------------
If your server is already running Windows NT 4.0, then use
the following steps to add the PERC/CERC Windows NT 4.0
driver.
1) Insert the PERC/CERC driver diskette created above in
appropriate drive. The driver files can also be installed
from a local or network drive.
2) Click on Start > Control Panel > Settings. Double-click
on the Small Computer System Interface (SCSI) Adapter
icon.
3) Select the Drivers tab.
4) Click on the Add button.
5) Select Have Disk.
6) The Install From Disk box appears. Specify the location
of the PERC/CERC Windows NT 4.0 driver and click on OK.
7) Click on OK to add the PERC/CERC Windows NT 4.0 driver.
This procedure will install the PERC/CERC drivers for
Windows NT v4.0. You must reboot the system after
installation has been completed successfully.
Help en zelfstudies voor drivers
Ga voor meer downloads naar Drivers en downloads. Voor hulp bij het gebruik van de informatie op deze pagina, gaat u naar Hulp en zelfstudies voor drivers.