Ikke slå av datamaskinen eller koble fra strømkilden ved oppdatering av BIOS, da dette kan skade datamaskinen. Under oppdateringen starter datamaskinen på nytt, og en kort stund vil du se at skjermen er svart.
Før du oppdaterer, kan du lese installasjonsinstruksjonene og viktig informasjon som er angitt nedenfor.
Dell OptiPlex 9030 System BIOS
Omstart kreves Installert Denne filen ble automatisk installert som en del av en nylig oppdatering. Hvis du opplever problemer, kan du laste ned og installere på nytt manuelt.Innholdet på denne siden kan ha blitt oversatt automatisk. Fyll ut skjemaet nederst på siden for å gi tilbakemelding.
This package contains the Dell system BIOS update. BIOS is a firmware that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices.
Anbefalt
Sjekk kompatibilitet
Angi produktdetaljer for å vise den nyeste driverinformasjonen for systemetSkriv inn Dell-service-ID-en eller -modellen
Ønsker du å finne produktet? Skriv inn en produktidentifikator. Vis meg hvordan
Denne driveren er ikke kompatibel
Denne driveren er ikke gjeldende for det valgte produktet. Velg et annet produkt for å angi produktopplysningene dine for denne driveren på nytt, eller gå til siden for produktstøtte for å vise alle drivere for et annet produkt.
Logg på Windows som administrator for å bruke automatisk skanning. Hvis du allerede er logget på som administrator og ser denne meldingen, må du starte maskinen på nytt. Systemet ditt blir administrert av IT-administratoren, og funksjonene kan være begrenset.
Finn flere oppdateringer. Bruk SupportAssist for å finne alle de nyeste driveroppdateringene for enheten din.
Feilrettinger og forbedringer
- Update to the latest CPU microcode to address CVE-2017-5715 and associated Intel Reboot issue.
Les merVersjon
A19, A19
Utgivelsesdato
27 feb. 2018
Nedlastingstype
System-BIOS
Kategori
BIOS
Viktighet
KritiskDell Technologies anbefaler på det sterkeste at du installerer denne oppdateringen så snart som mulig. Oppdateringen inneholder viktige feilrettinger og endringer for å forbedre funksjonaliteten, påliteligheten og stabiliteten til Dell-systemet ditt. Den kan også inkludere sikkerhetsreparasjoner og andre funksjonsforbedringer.
Tilgjengelige formater
Filformat: CPG BIOS-kjørbar fil for Windows/DOS
Filnavn: OptiPlex_9030_AIO_A19.exe
Filstørrelse: 9.49 MB
Dette er en stor fil. Avhengig av tilkoblingshastigheten kan det ta litt tid å laste den ned.
Formatbeskrivelse:
Dette filformatet består av en BIOS-kjørbar fil. Universalformatet (Windows / MS DOS) kan brukes til å installere fra et hvilket som helst Windows- eller MS DOS-miljø.
Kontroller kontrollsumverdien for å sikre integriteten til nedlastingen.
MD5:
94b9d10f9ded6205e69b718fc1c4f092
SHA1:
4ac7273d246fffcbe52dedf11a4de191956192c6
SHA-256:
00812cf3a94d63809c0921e00e8096cf3eecddece9fb2381dc23cb958b1b18db
Ved å laste ned godtar du vilkårene i lisensavtalen for Dell-programvare. (på engelsk)
Gjelder
OptiPlex 9030 AIO
Instruksjoner for installasjon
Updating the BIOS from Windows
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_9030_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_9030_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes, and reboot the system.
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Download and Installation
1. Click Download File, to download the file.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file and double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS (Non-Windows users)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_9030_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_9030_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Go to Exit > Save Changes, and reboot the system.
Trenger du hjelp med BIOS-problemer?
Finn en løsning i Dells feilsøkingsveiledning for BIOSHjelp og veiledninger for drivere
Hvis du vil ha flere nedlastinger, kan du gå til Drivere og nedlastinger. For å få hjelp til å bruke informasjonen på denne siden, kan du gå til Driverhjelp og opplæring