Adaptec PERC3/Di, v., A11

This software contains v2.8.1.6098 Firmware for the PowerEdge 2500/2500SC & PowerVault PV750N PERC 3/Di controller.

Pobierz najnowszy sterownik

Wprowadź dane produktu, aby wyświetlić najnowsze informacje o sterowniku systemowym.

Ten sterownik jest niezgodny

Ten sterownik jest aktualny

Informacje o sterowniku są aktualne. Aby wyświetlić wszystkie sterowniki do produktu , przejdź na stronę Sterowniki i pliki do pobrania.

Poprawki i usprawnienia

Fixes and Enhancements
2.8.1 Build 6098
- fixed an issue which occurs when reconfiguring an array with CLI while array was under stress; can result in kernel panic in Linux.
- fixed a bug where a 300GB hard drive could not be assigned as a hot spare for a 300GB R1 using full drive capacities.

2.8.1 Build 6097
-fixed a defect which occurs when reconfiguring an array to a size greater than 1.09 terabytes; can result in data loss.
–fixed bug where previous firmware did not re-calculate disk capacity when a drive is replaced.

2.8.0 Build 6095
-single bit change to turn off flag indicating 64-bit compatibility. Needed to fix OMSS Enclosure support issue with RHEL4.

2.8.0 Build 6092
-Background controller cache flush routine modified to flush smaller number of buffers during I/O without impacting RAID throughput. This change fixes driver timeout (manifesting as loss of drive access and filesystem errors like ext3_get_inode_loc errors) seen under certain Linux configurations.

2.8.0 Build 6089
-Default changed to 30 Second Timeout for controller BIOS option to pause or continue when RAID configuration is found altered or degraded. This behavior is same as pre v2.8 firmware behavior.

2.8.0 Build 6082 - Initial release of v2.8 firmware
-The ROMB firmware modified eliminating need for separate SCSI driver when channel-B is configured
as SCSI. Now only one driver is needed for both RAID/RAID and RAID/SCSI configurations (not applicable to PERC2/QC).
-Controller BIOS option added to pause or continue after 30 seconds timeout when RAID configuration is found altered or degraded.
-Additional ESM fix for pulled/missing drives.
-HIM_PCI_ERR correction to power management interrupt.
-Cache flush loop decreased to prevent extensive spin-lock hold during high I/O.
-AFU fix to block firmware installation based on proper level System BIOS.
-SCSI Passthru Event filtering.
-Disallow selection of drive to create raid when already reach maximum limit.
-Disable interrupts around doing queue accesses in CompleteFIB( ).


Wersja, A11



Data wydania:

13 paź 2005

Ostatnia aktualizacja:

03 lis 2011


Dostępne formaty

Format pliku: Floppy
Nazwa pliku: PE2500-PV750N-281_6098-A11.exe
Rodzaj pobierania: HTTP
Rozmiar pliku: 1.04 MB
Opis formatu:
Ten plik zawiera skompresowane archiwum lub zestaw plików. Pobierz plik do folderu na dysku twardym, a następnie kliknij go dwukrotnie, aby rozpakować zestaw plików. Postępuj według instrukcji, aby dokończyć instalację.
To ensure the integrity of your download, please verify the checksum value.
Format pliku: Update Package for Red Hat Linux
Nazwa pliku: PE2500_PV750N_RAID_FW_LX_A11.BIN
Rodzaj pobierania: HTTP
Rozmiar pliku: 1.87 MB
Opis formatu:
Pakiety Dell Update Package dla systemu Linux można wykorzystywać jako samodzielne aplikacje, które sprawdzają określone kryteria poprawności, a następnie stosują aktualizację.
Uwaga: pakiety Dell Update Package dla systemu Linux stanowią oprogramowanie open source. Więcej informacji zawiera plik readme dołączony do tych pakietów.
To ensure the integrity of your download, please verify the checksum value.
Format pliku: Update Package for Microsoft® Windows®
Nazwa pliku: PE2500_PV750N_RAID_FW_WIN_A11.EXE
Rodzaj pobierania: HTTP
Rozmiar pliku: 1.93 MB
Opis formatu:
Pakiety aktualizacyjne firmy Dell w formacie dla 32-bitowego systemu Microsoft Windows można uruchamiać również w 64-bitowych wersjach systemu Microsoft Windows. Pakiety aktualizacyjne firmy Dell w formacie dla 64-bitowego systemu Microsoft Windows działają tylko w 64-bitowych wersjach tego systemu. Wybierając aktualizację sterownika urządzenia, upewnij się, że wybierasz wersję odpowiednią dla swojego systemu operacyjnego.
To ensure the integrity of your download, please verify the checksum value.

Pobierając plik, akceptujesz warunki umowy licencyjnej na oprogramowanie firmy Dell. (w języku angielskim)

Instructions for PE2500-PV750N-281_6098-A11.exe


1. Click the Download Now link to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.

Diskette Creation
1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set.
2. Insert a blank diskette then click Continue.
3. When prompted, repeat step 2 until you reach the end of the diskette set. Label each diskette with a disk number starting from 1.
4. After all the files have been copied to the last diskette, click Finish.

Firmware Installation
The firmware update utility on this diskette is DOS-based and named AFU.EXE. It offers both interactive and command line modes.

Performing the PERC 3/Di Firmware Upgrade in Interactive Mode
The AFU interactive mode is entered by issuing the AFU command with no command line switches. This mode simplifies the firmware update process for PERC 3/Di when one or more PERC 2/3 controllers are present.

To update the firmware using the AFU interactive mode, follow these steps:

1. Shut down your system.

2. Reboot the system with the diskette labeled:
DELL PERC 3/Di Firmware
Disk 1 of 2

***NOTE: If the system has not been set up to boot from the diskette, please read system documentation for instructions on how to set this up.

3. At the DOS prompt, enter the following command and press ENTER:

A:\> AFU

This starts the AFU in interactive mode. The AFU will detect the integrated PERC 3/Di and any installed PERC 2 controllers and present them for selection in a list.

4. If only PERC 3/Di is detected then AFU will select it. Otherwise, using the arrow keys, highlight PERC 3/Di and select it by pressing the space bar and press ENTER.

5. A "Select an Operation" menu will be presented. Select the following option and press ENTER:

Update flash image

6. The AFU will issue the following message:

Update from the flash image file in directory:
Change the directory if necessary, then use the TAB key to select the OK box, and press ENTER.

7. AFU will issue following message:

Reading flash image file (Build xxxx)...

8. AFU will issue following message after reading flash image from first diskette:

Please insert disk labeled "PERC 3/Di Firmware disk 2"

9. Insert the second diskette and press ENTER.

10. AFU will complete reading the flash image and issue following message:

AFU is about to update firmware on controller(s) Dell PERC 3/Di
This might take a few minutes. Select OK to continue.

11. Select the OK box, then press ENTER. AFU will proceed to update the firmware and issue following message:

Writing PERC 3/Di integrated flash image to controller 0 ...

This message will be followed by additional progress messages. When the flash update has completed, you will see this message:

Controller #0 Dell PERC 3/Di
Flash image was updated and verified successfully

***NOTE: If you selected multiple controllers, AFU will prompt you to insert the diskette after the successful update of first controller. Please insert firmware diskette 1 for second controller.

12. Press any key, then press the ESC key to exit AFU. Remove any diskettes from the drive and reboot the system.

***NOTE: System must be rebooted after performing firmware update on PERC 3/Di before attempting any access to drives attached to the controller.

Performing the Controller Firmware Upgrade in Command Line Mode
AFU in command line mode returns its exit status (zero for success or non-zero for an error) in the DOS environment variable ERRORLEVEL.

The following instructions explain how to upgrade the control

Pomoc i poradniki dotyczące sterowników