Driver Details

LITEONIT Solid State Drive Firmware Update

This package provides the firmware for LITEONIT LMT-128L9M mSATA 128GB, Revision HM7110e, and is supported on Inspiron, Latitude, Precision and XPS models running the following Windows operating systems: Windows 7, Windows 8 and Windows 10.

Fixes & Enhancements

- Improves compatibility with low power mode

- Not applicable


Version HM7110E, A03


Serial ATA

Release date

06 Oct 2015

Last Updated

30 Oct 2015


Available formats

File Format:Hard-Drive
File Name:LMT-128L9M-HM7110E_ZPE.exe
Download Type:HTTP
File Size: 2 MB
Format Description:This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, and then run (double-click) it to unzip the set of files. Follow the instructions to complete the installation.
To ensure the integrity of your download, please verify the checksum value.

By downloading, you accept the terms of the Dell Software License Agreement.

HM7110D,A02 30 Apr 20156:16:14 AM
HM7110B,A01 02 May 20144:05:35 PM
Supported Operating Systems
Windows 7, 32-bit
Windows 7, 64-bit
Windows 8, 32-bit
Windows 8, 64-bit
Windows 8.1, 32-bit
Windows 8.1, 64-bit
Windows 10, 32-bit
Windows 10, 64-bit
Applies to
Installation instructions

1. Click Download File and follow the remaining prompts to download the file.
2. When the File Download window appears, click Run to unzip the download package into your hard drive.
3. The file explorer will open pointing to the directory containing the download package. Please take note of the path.
4. Change file extension from .ex to .exe.


Firmware upgrade through the Windows utility

1. Backup the user data in Solid-State Drive.
2. Switch to AC Power.
3. Put targeted SSD which want to be flashed FW as slave drive or use it as external storage device drive via the USB port.
4. New FW only can be actived after reboot or power reset.
5. This utility can face flash FW by the same FW version SSD, that is it will face flash FW HMx110E/HM9110F/6M8410D again if the FW in target SSD is HMx110E/HM9110F/6M8410D already.

1. Run the utility contained therein to start firmware update process.
2. On the first screen, if the target SSD is not listed, select it and then Click "Update".
3. The next screen is a warning message. It states the risks and reminds user to backup important files before proceeding. Please click OK to proceed.
4. Firmware upgrade will proceed. When the firmware upgrade process completes, the user will be prompted to reboot the machine. Please close all open applications and save your work before rebooting your machine.
5. The system will reboot and load the firmware. Once the firmware update is complete (screen will show firmware update done), you can boot into Windows.
6. To confirm the firmware update was successful, open Device manager -> open SSD -> click Properties -> choose hardware ID under Details and check the firmware version.

Important Information
WARNING: As with all firmware updates, it is strongly recommended that you backup or make copies of all important files before performing this update. This firmware update process is done entirely at your own risk. If performed correctly, there will be no loss of system or user data on the drive. However, if the firmware process is interrupted for any reason, your solid state drive may not function properly.
Warning: Do not turn off your computer or disconnect from your power source while updating the BIOS or you may harm your computer. During the update, your computer will restart and you will briefly see a black screen.

This driver has been tested by both the independent software vendor (ISV) and Dell on the operating systems, graphics cards, and application supported by your device to ensure maximum compatibility and performance. Details

Dell recommends applying this update during your next scheduled update cycle. The update contains feature enhancements or changes that will help keep your system software current and compatible with other system modules (firmware, BIOS, drivers and software).