Mainframe Enablers TF Clone/Snap: 작업이 성공적으로 완료되지만 VOLUME 작업이 EQCA128E 메시지와 함께 완료됩니다.
Summary: SNAP VOLUME 작업 중에는 모든 기능이 성공적으로 실행되었음에도 불구하고 오류 EQCA128E 메시지가 나타납니다.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Symptoms
SNAP VOLUME 작업에 대한 오류 메시지가 발행됩니다.
EQCA128E UNABLE TO DETERMINE REMOTE DA FOR SYSCALL EXECUTION -00-00-00-
Cause
이 문제는 Mainframe Enablers 10.0.0 및 10.1.0에 대한 C2403 유지 관리에서 도입되었습니다.
*** TIMEFINDER MF SNAP V10.1.0 (019) - SCF V10.01.00 (0009) *** *** TIMEFINDER MF SNAP V10.0.0 (045) - SCF V10.00.00 (0064) ***
Resolution
영구 수정:
Additional Information
PTF 커버 레터:
MFE 10.1 SNA1024:
++PTF(SNA1024) REWORK(2024124) .
++VER(Z038) FMID(SSNPA10)
PRE(
SNA1020
)
/*
*-------------------------------------------------------------
* PROBLEM DESCRIPTION(S):
* ------------------------------------------------------------
* PROBLEM FIXED: MFE-17116
* USERS AFFECTED: SnapVX and TF/Clone users
* PROBLEM DESCRIPTION: Error message EQCA128E is displayed
* when running SnapVX or TF/Clone
* commands using remote syntax.
* DESCRIPTION DETAIL:
*
* Error message 'EQCA128E UNABLE TO DETERMINE REMOTE DA FOR
* SYSCALL EXECUTION 00-00-00' is displayed when running
* SnapVX or TF/Clone commands using remote syntax. This
* message should not be printed for VMAX/PowerMax systems
* running microcode 5876 or higher.
*
* PROBLEM RESOLUTION:
*
* SnapVX and TF/Clone have been updated to avoid printing the
* EQCA128E message for VMAX/PowerMax systems running microcode
* 5876 and higher.
*
* MODULES: EMCQCAPL
*
* ------------------------------------------------------------
* SNA1024 3 May 2024 18:02:38
* ------------------------------------------------------------
* OPT Summary
* The following OPT was addressed by this PTF:
*
* MFE-17116
*
*-------------------------------------------------------------
*/ .
MFE 10.0 SNA0048:
++PTF(SNA0048) REWORK(2024109) .
++VER(Z038) FMID(SSNPA00)
PRE(
SNA0047
)
/*
*-------------------------------------------------------------
* PROBLEM DESCRIPTION(S):
* ------------------------------------------------------------
* PROBLEM FIXED: MFE-17117
* USERS AFFECTED: SnapVX and TF/Clone users
* PROBLEM DESCRIPTION: Error message EQCA128E is displayed
* when running SnapVX or TF/Clone
* commands using remote syntax.
* DESCRIPTION DETAIL:
*
* Error message 'EQCA128E UNABLE TO DETERMINE REMOTE DA FOR
* SYSCALL EXECUTION 00-00-00' is displayed when running
* SnapVX or TF/Clone commands using remote syntax. This
* message should not be printed for VMAX/PowerMax systems
* running microcode 5876 or higher.
*
* PROBLEM RESOLUTION:
*
* SnapVX and TF/Clone have been updated to avoid printing the
* EQCA128E message for VMAX/PowerMax systems running microcode
* 5876 and higher.
*
* MODULES: EMCQCAPL
*
* ------------------------------------------------------------
* SNA0048 18 Apr 2024 19:55:53
* ------------------------------------------------------------
* OPT Summary
* The following OPT was addressed by this PTF:
*
* MFE-17117
*
*-------------------------------------------------------------
*/ .
Affected Products
Mainframe EnablersArticle Properties
Article Number: 000223689
Article Type: Solution
Last Modified: 09 يونيو 2026
Version: 2
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.