DELL Networking SONiC: Como configurar o endereço IPv4 e a unidade máxima de transmissão em interfaces de camada 3
Resumen: Este artigo explica como configurar o endereço IPv4 e as interfaces de unidade máxima de transmissão (MTU) no Dell Networking SONiC. Este artigo usa um switch que executa o Dell SONiC 4.1. ...
Este artículo se aplica a
Este artículo no se aplica a
Este artículo no está vinculado a ningún producto específico.
No se identifican todas las versiones del producto en este artículo.
Instrucciones
|
Pré-requisitos
Estamos usando a nomenclatura de interface padrão para demonstrar os conceitos. Consulte o artigo da Dell 202172 Dell Networking Série S: Configuração básica da interface — SONiC 4.0 para obter mais informações sobre nomenclatura de interface |
Índice
Atribua um endereço IP.
Sintaxe de configuração
| Comando | Explicação |
|---|---|
admin@DELLSONiC:~$ sonic-cli |
Entrar na interface de linha de comando de gerenciamento da Dell |
DELLSONiC# configure terminal |
Entrar no modo de configuração |
DELLSONiC(config)# interface <Eth slot/port><Vlan ID><PortChannel ID><Eth slot/port.subport><Loopback ID> |
Configurar interface, VLAN, PortChannel, subinterface, loopback. |
DELLSONiC(conf-if-XXXX)# ip address A.B.C.D/mask |
Configure o endereço IP com máscara. |
DELLSONiC(conf-if-XXXX)# no ip address A.B.C.D/mask |
Remova o endereço IP. |
DELLSONiC(conf-if-XXXX)# no shutdown |
Se a interface estiver desligada, desligue-a. |
Mostrar um comando para verificar o endereço IP.
| Comando | Explicação |
|---|---|
admin@DELLSONiC:~$ sonic-cli |
Entrar na interface de linha de comando de gerenciamento da Dell |
DELLSONiC# configure terminal |
Entrar no modo de configuração |
DELLSONiC# show ip interfaces |
Mostrar IP configurado em Interfaces. |
DELLSONiC# show running-configuration interface <Eth slot/port><Vlan ID><PortChannel ID><Loopback ID> |
Mostrar configuração da interface |
Vamos configurar um endereço IP na interface Eth 1/1 com o endereço IP 10.0.0.1/24.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface Eth 1/1 DELLSONiC(config-if-Eth1/1)# ip address 10.0.0.1/24 DELLSONiC(config-if-Eth1/1)# end DELLSONiC# |
Vamos verificar a configuração.
DELLSONiC# show ip interfaces Flags: U-Unnumbered interface, A-Anycast IP ----------------------------------------------------------------------------------------------------------------- Interface IP address/mask VRF Admin/Oper Flags ----------------------------------------------------------------------------------------------------------------- Eth1/1 10.0.0.1/24 up/up |
DELLSONiC# show running-configuration interface Eth 1/1 ! interface Eth1/1 mtu 9100 no shutdown ip address 10.0.0.1/24 DELLSONiC# |
Vamos configurar o endereço IP na VLAN 1 com o endereço IP 10.0.0.1/24.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface Vlan 1 DELLSONiC(config-if-Vlan1)# ip address 10.0.0.1/24 DELLSONiC(config-if-Vlan1)# end DELLSONiC# |
Vamos verificar a configuração.
DELLSONiC# show ip interfaces Flags: U-Unnumbered interface, A-Anycast IP ----------------------------------------------------------------------------------------------------------------- Interface IP address/mask VRF Admin/Oper Flags ----------------------------------------------------------------------------------------------------------------- Vlan1 10.0.0.1/24 up/up |
DELLSONiC# show running-configuration interface Vlan 1 ! interface Vlan1 ip address 10.0.0.1/24 |
Vamos configurar o endereço IP no PortChannel 1 com o endereço IP 10.0.0.1/24.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface PortChannel 1 DELLSONiC(config-if-po1)# ip address 10.0.0.1/24 DELLSONiC(config-if-po1)# end |
Vamos verificar a configuração.
DELLSONiC# show ip interfaces Flags: U-Unnumbered interface, A-Anycast IP ----------------------------------------------------------------------------------------------------------------- Interface IP address/mask VRF Admin/Oper Flags ----------------------------------------------------------------------------------------------------------------- PortChannel1 10.0.0.1/24 up/up |
DELLSONiC# show running-configuration interface PortChannel 1 ! interface PortChannel1 no shutdown ip address 10.0.0.1/24 DELLSONiC# |
Vamos configurar o endereço IP no Loopback 1 com o endereço IP 10.0.0.1/32.
Nota: O loopback suporta apenas o comprimento do prefixo /32 ou a sub-rede.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface Loopback 1 DELLSONiC(config-if-lo1)# ip address 10.0.0.1/32 DELLSONiC(config-if-lo1)# end DELLSONiC# |
Vamos verificar a configuração.
DELLSONiC# show ip interfaces Flags: U-Unnumbered interface, A-Anycast IP ----------------------------------------------------------------------------------------------------------------- Interface IP address/mask VRF Admin/Oper Flags ----------------------------------------------------------------------------------------------------------------- Loopback1 10.0.0.1/32 up/up |
DELLSONiC# show running-configuration interface Loopback 1 ! interface Loopback 1 ip address 10.0.0.1/32 DELLSONiC# |
Atribuir endereço IP do AnycastConsulte o artigo Dell Networking SONiC: como configurar o gateway estático Anycast (endereço anycast) sobre como configurar o endereço anycast. |
MTU
Sintaxe de configuração
| Comando | Explicação |
|---|---|
admin@DELLSONiC:~$ sonic-cli |
Entrar na interface de linha de comando de gerenciamento da Dell |
DELLSONiC# configure terminal |
Entrar no modo de configuração |
DELLSONiC(config)# interface <Eth slot/port><Vlan ID><PortChannel ID><Eth slot/port.subport> |
Configurar interface, VLAN, PortChannel, subinterface. |
DELLSONiC(conf-if-XXXX)# mtu <MTU> |
Configurar MTU Alterar MTU (1312 para 9216). Padrão 9100 |
DELLSONiC(conf-if-XXXX)# no mtu |
Configure a MTU padrão na interface (o padrão é 9100). |
Mostrar comandos para verificar a MTU.
| Comando | Explicação |
|---|---|
admin@DELLSONiC:~$ sonic-cli |
Entrar na interface de linha de comando de gerenciamento da Dell |
DELLSONiC# configure terminal |
Entrar no modo de configuração |
DELLSONiC# show interface <Eth slot/port><Vlan ID><PortChannel ID> |
Mostrar detalhes da interface. |
DELLSONiC# show running-configuration interface <Eth slot/port><Vlan ID><PortChannel ID> |
Mostrar configuração da interface |
DELLSONiC#show interface status |
Mostrar status da interface |
-
Notas sobre a configuração da MTU
- Configure a MTU nos membros da VLAN antes de configurar a MTU da VLAN. Todos os membros de uma VLAN devem ter o mesmo valor de MTU. Os membros marcados devem ter uma MTU de link 4 bytes maior do que os membros sem marca para contabilizar a tag de pacote.
- Configure a MTU nos membros do port channel antes de configurar a MTU do port channel. Todos os membros de um port channel devem ter o mesmo valor de MTU. Os membros marcados devem ter uma MTU de link 4 bytes maior do que os membros sem marca para contabilizar a tag de pacote.
- Certifique-se de que a MTU dos membros do port channel seja maior ou igual à MTU do port channel. Se você configurar a MTU nos membros do port channel depois de configurar a MTU do port channel, a MTU do port channel pode não ser atualizada. O sistema seleciona o menor valor de MTU configurado no port channel ou nos membros do port channel para ser o MTU do port channel. Por exemplo, o port channel contém membros marcados com MTU de link de 1522 e MTU IP de 1500, e membros sem marcação com MTU de link de 1518 e MTU de IP de 1500. A MTU de link do port channel não pode ter mais de 1518 bytes e a MTU de IP não pode ser maior que 1500 bytes.
Vamos configurar a MTU na interface Eth 1/1.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface Eth 1/1 DELLSONiC(config-if-Eth1/1)# mtu 1500 DELLSONiC(config-if-Eth1/1)# end |
Vamos verificar a configuração (saída grepped para brevidade).
DELLSONiC# show interface status -------------------------------------------------------------------------------------------------------------------------------------- Name Description Oper Reason AutoNeg Speed MTU Alternate Name -------------------------------------------------------------------------------------------------------------------------------------- Eth1/1 - up oper-up off 25000 1500 Ethernet0 |
DELLSONiC# show running-configuration interface Eth 1/1 ! interface Eth1/1 mtu 1500 no shutdown |
DELLSONiC# show interface Eth 1/1 Eth1/1 is up, line protocol is up, reason oper-up Hardware is Eth, address is xx:xx:xx:xx:xx:xx Mode of IPV4 address assignment: not-set Mode of IPV6 address assignment: not-set Interface IPv6 oper status: Disabled IP MTU 1500 bytes LineSpeed 25GB, Auto-negotiation off Link-training: off |
Vamos configurar a MTU na interface VLAN.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface Vlan 1 DELLSONiC(config-if-Vlan1)# mtu 1500 DELLSONiC(config-if-Vlan1)# end DELLSONiC# |
Vamos verificar a configuração (saída grepped para brevidade).
DELLSONiC# show interface Vlan 1 Vlan1 is up, line protocol is up Hardware is Vlan, address is xx:xx:xx:xx:xx:xx Mode of IPV4 address assignment: not-set Mode of IPV6 address assignment: not-set Interface IPv6 oper status: Disabled IP MTU 1500 bytes Time since last interface status change: 02:33:17 |
DELLSONiC# show running-configuration interface Vlan 1 ! interface Vlan1 mtu 1500 |
Vamos configurar o PortChannel 1 com MTU 1500.
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)# interface PortChannel 1 DELLSONiC(config-if-po1)# mtu 1500 DELLSONiC(config-if-po1)# end DELLSONiC# |
Vamos verificar a configuração (saída grepped para brevidade).
DELLSONiC# show running-configuration interface PortChannel 1 ! interface PortChannel1 mode on mtu 1500 no shutdown |
DELLSONiC# show interface status -------------------------------------------------------------------------------------------------------------------------------------- Name Description Oper Reason AutoNeg Speed MTU Alternate Name -------------------------------------------------------------------------------------------------------------------------------------- Eth1/1 - up oper-up off 25000 1500 Ethernet0 Eth1/2 - up oper-up off 25000 1500 Ethernet1 PortChannel1 - up oper-up - 25000 1500 - |
DELLSONiC# show interface PortChannel 1 PortChannel1 is up, line protocol is up, reason oper-up, mode Static Hardware is PortChannel, address is xx:xx:xx:xx:xx:xx Minimum number of links to bring PortChannel up is 1 Mode of IPV4 address assignment: not-set Mode of IPV6 address assignment: not-set Graceful shutdown: Disabled MTU 1500 LineSpeed 25.0GB Events: |
Productos afectados
Enterprise SONiC Distribution, PowerSwitch E3200-ON Series, Dell EMC Networking N3200-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5232F-ON, PowerSwitch S5248F-ON, PowerSwitch S5296F-ON, PowerSwitch Z9264F-ON, PowerSwitch Z9332F-ON
, PowerSwitch Z9432F-ON
...
Propiedades del artículo
Número del artículo: 000218581
Tipo de artículo: How To
Última modificación: 10 abr 2024
Versión: 5
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.