使用 ROUTE REFRESH 进行 DELL Networking OS10 BGP 软重置
Resumen: DELL Networking OS10 支持 RFC 2918 中提到的 BGP ROUTE REFRESH 功能。本文介绍带路由刷新的 BGP 软重置,以及与 DELL Networking OS10 中的 BGP 硬重置或软重置与软重置的比较。
Este artículo se aplica a
Este artículo no se aplica a
Este artículo no está vinculado a ningún producto específico.
No se identifican todas las versiones del producto en este artículo.
Instrucciones
更改路由策略可能需要重置 BGP 会话。这可以通过使用 BGP Hard Reset 或 Soft reset with soft-reconfiguration 或 Soft Reset with Route Refresh 来实现。
以下是 BGP 硬重置、软重置和动态入站软重置之间的比较。
在 DELL Networking OS10 中,任何路由映射或前缀列表或 BGP 属性更改均会正常地通告给相关的 BGP 对等体,因此在 DELL OS10 中不需要软重置出站。这就是 DELL OS10 CLI 中不存在“clear ip bgp soft out”命令的原因。
输出示例:
以下是 BGP 硬重置、软重置和动态入站软重置之间的比较。
| BGP 硬重置 | 使用软重新配置进行 BGP 软重置 | 使用路由刷新软重置(首选方法) |
|---|---|---|
| 执行 BGP 硬重置会关闭 TCP 会话。 即重新建立 BGP 邻居关系。 |
对等节点之间的 TCP 会话不受影响。即 BGP 邻居不受影响。 | 对等节点之间的 TCP 会话不受影响。即 BGP 邻居不受影响。 |
| 启动邻居形成和路由学习的整个过程。 | 由于来自存储在单独表中的邻居的路由信息,因此需要额外的内存。然后,将应用更改并将其存储在路由表中。 仅对于不支持路由刷新功能的路由器,建议使用此方法。 |
路由刷新将发送到使用所需的路由表信息进行响应的邻居。 |
| 无需特殊配置 | 必须配置邻居软重新配置入站。 | 无需特殊配置 |
| 对等节点不需要特殊对等功能 | 对等节点不需要特殊对等功能 | 两个 BGP 对等节点都必须支持路由刷新功能。 如何验证 BGP 邻居是否支持 ROUTE REFRESH 功能。 |
| 影响 BGP 邻居整个前缀的流量 | 仅影响受策略更改影响的特定前缀。 | 仅影响受策略更改影响的特定前缀。 |
使用软重置和路由刷新的命令语法
| 命令 | 说明 |
|---|---|
| OS10# clear ip bgp * 软输入 | 激活策略而不重置所有 BGP 邻居的 BGP TCP 会话。 |
| OS10# clear ip bgp soft in | 在不重置指定 BGP 邻居的 BGP TCP 会话的情况下激活策略。 |
为什么 DELL Networking OS10 没有 BGP 软重置出站?
在 DELL Networking OS10 中,任何路由映射或前缀列表或 BGP 属性更改均会正常地通告给相关的 BGP 对等体,因此在 DELL OS10 中不需要软重置出站。这就是 DELL OS10 CLI 中不存在“clear ip bgp soft out”命令的原因。
如何验证 BGP 邻居是否支持ROUTE_REFRESH功能
检查 show ip bgp neighbor 并验证从邻居收到的功能 是否 ROUTE_REFRESH(2)。输出示例:
R1# show ip bgp neighbors 10.0.0.2
BGP neighbor is 10.0.0.2, remote AS 100, local AS 1 external link
BGP version 4, remote router ID 2.2.2.6
BGP state ESTABLISHED, in this state for 01:00:15
Last read 01:20:12 seconds
Hold time is 180, keepalive interval is 60 seconds
Configured hold time is 180, keepalive interval is 60 seconds
Fall-over disabled
Received 84 messages
3 opens, 1 notifications, 5 updates
69 keepalives, 6 route refresh requests
Sent 84 messages
7 opens, 1 notifications, 2 updates
71 keepalives, 3 route refresh requests
Minimum time between advertisement runs is 30 seconds
Minimum time before advertisements start is 0 seconds
Capabilities received from neighbor for IPv4 Unicast:
MULTIPROTO_EXT(1)
ROUTE_REFRESH(2) ======================================>Note
CISCO_ROUTE_REFRESH(128)
4_OCTET_AS(65)
Capabilities advertised to neighbor for IPv4 Unicast:
MULTIPROTO_EXT(1)
ROUTE_REFRESH(2)
CISCO_ROUTE_REFRESH(128)
4_OCTET_AS(65)
Prefixes accepted 5, Prefixes advertised 3
Connections established 2; dropped 1
Maximum prefix limit reached sent 01:03:15 ago
For address family: IPv4 Unicast
Allow local AS number 0 times in AS-PATH attribute
Prefixes ignored due to:
Martian address 0, Our own AS in AS-PATH 0
Invalid Nexthop 0, Invalid AS-PATH length 0
Wellknown community 0, Locally originated 0
For address family: IPv6 Unicast
Allow local AS number 0 times in AS-PATH attribute
Local host: 10.0.0.1, Local port: 179
Foreign host: 10.0.0.2, Foreign port: 41230Productos afectados
Dell EMC Networking N3200-ON, PowerSwitch S4112F-ON/S4112T-ON, PowerSwitch S4128F-ON/S4128T-ON, PowerSwitch S4148F-ON/S4148T-ON/S4148FE-ON, PowerSwitch S4148U-ON, PowerSwitch S4248FB-ON /S4248FBL-ON, PowerSwitch S5148F-ON, PowerSwitch Z9100-ON
, PowerSwitch Z9264F-ON, PowerSwitch Z9432F-ON, SmartFabric OS10 Software
...
Propiedades del artículo
Número del artículo: 000210800
Tipo de artículo: How To
Última modificación: 11 oct 2023
Versión: 2
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.