Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Número del artículo: 000121440

How to configure MAC based port security on Dell N2000, N3000, and N4000 series switches.

Resumen: Dell EMC Networking N-Series configuring MAC based port security on switches.

Es posible que este artículo se traduzca automáticamente. Si tiene comentarios sobre su calidad, háganoslo saber mediante el formulario en la parte inferior de esta página.

Contenido del artículo

Instrucciones

Article Summary: This article shows how to configure MAC based port security on Dell N Series switches



Table of Contents
 

 
  1. How to enable MAC based port security on the N Series Switch
  2. How to statically add MAC address to an Interface
  3. How to configure a maximum amount of allowed MAC addresses
  4. How to configure the maximum limit of dynamically learned mac addresses on a specific interface
 

How to enable MAC based port security on the N series switch

   
Command Parameters
console>enable Enter enable Privilege Exec mode.
console#config Enter configuration mode.
console(config)#switchport port-security Enable port security globally on the switch.  
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-gi1/0/5)#switchport port-security Enable port security on the interface level.
   
 
HOW10392_en_US__1icon Note: When port security is enabled on an interface, all dynamic MAC addresses learned on that port are removed, and the port re-learns any MAC addresses on that interface.
 


How to statically add MAC addresses to an interface

   

 

Command Parameters
console#config Enter configuration mode.
console(config)# mac address-table static c2f3.220a.12f4 vlan 1 interface gi1/0/5 This adds the MAC address c2f3.220a.12f4 to the MAC table for interface gi1/0/5.
console(config)#no mac address-table static c2f3.220a.12f4 vlan 1 interface gi1/0/5 Add "no" to the beginning of the command to remove the MAC address.

 

How to configure a maximum amount of allowed Static MAC addresses

   
Command Parameters
console#config Enter configuration mode.
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-Gi1/0/5)#switchport port-security maximum 3 Sets the max limit of static MAC addresses to 3.  Range is <0-100>  Default is 100.
   
 
HOW10392_en_US__1icon Note: To clear dynamically learned MAC addresses from a port, you must perform the following example command.
console#clear mac address-table dynamic interface gi1/0/5
   
 
HOW10392_en_US__1icon Note: By default when port security violations occur, the port discards any frames on that interface originating from violating MAC addresses. The port is not shut down.  If you are wanting the port to actually shut down you will need to add this command to the specific interfaces that require that feature:  
(config-if-Gi1/0/5)#switchport port-security violation shutdown : 
   
 


How to configure the maximum limit of dynamically learned mac addresses on a specific interface

 

 
Command Parameters
console#config Enter configuration mode.
console(config)#interface gi1/0/5 Enter specific interface that needs port security.
console(config-if-gi1/0/5)#switchport port-security dynamic 0 This example uses 0 as you would normally want the port not to learn macs dynamically.  Range is <0-600>   Default is 100.

 

 

Propiedades del artículo

Producto comprometido

PowerSwitch N2000 Series, PowerSwitch N3000 Series, PowerSwitch N4000 Series

Fecha de la última publicación

21 feb 2021

Versión

3

Tipo de artículo

How To

Volver al principio