Omitir para ir al contenido principal
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
Es posible que algunos números de artículo hayan cambiado. Si esto no es lo que está buscando, intente buscar todos los artículos. Buscar artículos

Procedure To Set S50N/V To Factory Default Configuration

Este artículo se aplica a Este artículo no se aplica a Este artículo no está vinculado a ningún producto específico. No se identifican todas las versiones del producto en este artículo.

Instrucciones

To reset the S50 to factory defaults, complete the following instructions.
  1. Connect to S50N/V device via console
    • Baud rate = 9600
    • Character Size = 8
    • Flow Control = Disabled
    • Stop Bits = 1
    • Parity = none​
  2. Power cycle the S50 either by disconnecting and reconnecting the power cord, or by typing reload, and then yes at privelidged exec mode
    • FTOS#reload
  3. Hit any key when prompted during the S50 boot process to get into BOOT_USER mode
U-Boot 1.1.4 (F10 Development) (Oct  6 2009 - 03:14:26)
Built by build at hydrogen on Tue Oct  6  3:14:25 2009
S-Series Boot selector Label 2.8.2.0

CPU:   8541, Version: 1.1, (0x807a0011)
Core:  E500, Version: 2.0, (0x80200020)
Clock Configuration:
       CPU: 660 MHz, CCB: 330 MHz,
       DDR: 165 MHz, LBC:  41 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: S50 Force10 Networks
       Watchdog enabled
DRAM:  Initializing
    DDR: 256 MB
Top of RAM usable for U-Boot at: 10000000
Reserving 122k for U-Boot at: 0ffe0000
Reserving 136k for malloc() at: 0ffbe000
Reserving 76 Bytes for Board Info at: 0ffbdfb4
Reserving 72 Bytes for Global Data at: 0ffbdf6c
Stack Pointer at: 0ffbdf48
New Stack Pointer is: 0ffbdf48
Now running in RAM - U-Boot at: 0ffe0000
L2 cache 256KB: enabled
Using default environment

PCI Scan: Found Bus 0, Device 22, Function 0
PCI Scan: Found Bus 0, Device 23, Function 0

In:    serial
Out:   serial
Err:   serial
U-Boot relocated to 0ffe0000
Net:   No ethernet found.
### main_loop entered: bootdelay=1

### main_loop: bootcmd="bootm 0xffe80000;setenv verify no;autoscr 0x1700000
bootm fe6000f0"
Hit any key to stop booting:  0
## Booting image at ffe80000 ...
   Image Name:   netbsd
   Image Type:   PowerPC NetBSD Standalone Program (uncompressed)
   Data Size:    383216 Bytes = 374.2 kB
   Load Address: 00040000
   Entry Point:  00040004
   Verifying Checksum ... OK
   Watchdog Disabled
   Loading Standalone Application ... OK
Unit 0
Unit 1
Registering ethernet driver for unit 0
Registering ethernet driver for unit 1

None of the boot parameters are configured!!
So Booting from flash!!

You can use U-boot native networking facilities
============================================================



Hit any key to break into BOOT_USER mode:  0  < ------------- hit any key
Starting F10 BLI Shell ...
BOOT_USER #

4. Enter "restore factory-defaults" command at the BOOT_USER prompt

BOOT_USER #restore factory-defaults

Erasing NVRAM contents...
Successfully erased NVRAM contents
Erasing Filesystem sectors...

Successfully erased filesystem sectors
Erasing boot parameters...
Successfully erased boot parameters
Please reload for restore factory-defaults to take effect.

5. Enter "reload" command to execute and the S50N/V system will boot up with factory default configuration (no need to hit any key during this boot up process)

BOOT_USER #reload
!
!
Force10>
Force10>en
Force10#00:07:00: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable password is required for authentication but not configured
00:07:00: %STKUNIT0-M:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success  on console

 
6.The switch is now factory defaulted and can be configured from here

Force10#config t
Force10(conf)#
 
Propiedades del artículo
Número del artículo: 000122552
Tipo de artículo: How To
Última modificación: 21 feb 2021
Versión:  3
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.